General Electric Create Jason Wu Casing Disassembly Repair Guide

Difficulty

Easy

Steps

Time Required

                          3 - 5 minutes

Sections

General Electric Create Jason Wu Casing Disassembly
4 steps

Flags

BackGeneral Electric Create Jason Wu
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              General Electric Create Jason Wu Casing Disassembly

Begin by removing the 5 screws (located: 2 screws on either side and 1 screw on the bottom) using the PH000 head in the Precision Phillips Screwdriver.
These screws were missing in our example. These screws should have been small Phillips PH000 screws 1.5mm in length.
These screws are very small. To keep from losing any pieces, place all small metals on a magnetic project mat.

Begin by removing the 5 screws (located: 2 screws on either side and 1 screw on the bottom) using the PH000 head in the Precision Phillips Screwdriver.

These screws were missing in our example. These screws should have been small Phillips PH000 screws 1.5mm in length.

These screws are very small. To keep from losing any pieces, place all small metals on a magnetic project mat.

1024

Step 2

After the screws are removed, pull the front casing up and away from the camera.
If the casing is difficult to remove, use a plastic opening tool to gently pry up on the front as shown.

After the screws are removed, pull the front casing up and away from the camera.

If the casing is difficult to remove, use a plastic opening tool to gently pry up on the front as shown.

Step 3

Using your hands or an opening tool, pry off the silver frame, taking special care at the top of the camera where the buttons are as it is a little harder to pry off.
If the back casing is loose from the camera body, it may be easier to perform step 4 first, then accomplish this step. Proceed as your unit allows.

Using your hands or an opening tool, pry off the silver frame, taking special care at the top of the camera where the buttons are as it is a little harder to pry off.

If the back casing is loose from the camera body, it may be easier to perform step 4 first, then accomplish this step. Proceed as your unit allows.

Step 4

The last part of the casing to disconnect is the back that houses the LCD screen.
The screen is attached by a connection ribbon. Gently pull the casing and screen away from the camera body to disconnect the casing.
The LCD screen is held onto the back casing by a small amount of adhesive. This may come loose during this process. Do not worry if they become separated.
This plug and the connection ribbon are fragile, try not to tear the connection ribbon when disconnecting.

The last part of the casing to disconnect is the back that houses the LCD screen.

The screen is attached by a connection ribbon. Gently pull the casing and screen away from the camera body to disconnect the casing.

The LCD screen is held onto the back casing by a small amount of adhesive. This may come loose during this process. Do not worry if they become separated.

This plug and the connection ribbon are fragile, try not to tear the connection ribbon when disconnecting.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.

Author

                                      with 4 other contributors

                    Kylan Hennessy

Member since: 01/23/2017

573 Reputation

                                      5 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       Eastern Washington University, Team 2-6, Crane Winter 2017                        

                                                  Member of Eastern Washington University, Team 2-6, Crane Winter 2017 



                    EWU-CRANE-W17S2G6                     


                                            4 Members                     


                                            7 Guides authored

Introduction#

What you need#

#

#

#

#

#

#

Team#

#

Introduction

What you need

Team