Difficulty

Easy

Steps

8

Time Required

                          10 - 15 minutes

Sections

2

  • Battery
  • 3 steps
  • Keyboard
  • 5 steps

Flags

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

  • BackGateway Solo 1450

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Make sure the device is powered down and disconnected from any power sources. Doing this will eliminate any electrical hazards while working on the device.
  • First it is necessary to locate the battery release button. With the laptop orientated so that the screen hinges are facing up the button is located about halfway up the laptop and slightly to the left.

Make sure the device is powered down and disconnected from any power sources. Doing this will eliminate any electrical hazards while working on the device.

First it is necessary to locate the battery release button. With the laptop orientated so that the screen hinges are facing up the button is located about halfway up the laptop and slightly to the left.

1024

Step 2

  • The next step is to simultaneously push up on the battery release button and to pull out on the battery itself. If this is not done simultaneously then the battery will not budge.

The next step is to simultaneously push up on the battery release button and to pull out on the battery itself. If this is not done simultaneously then the battery will not budge.

Step 3

  • To fully free the battery it is necessary to firmly grasp the battery and give it a firm tug.

To fully free the battery it is necessary to firmly grasp the battery and give it a firm tug.

Step 4

              Keyboard
  • Make sure the device is powered down and disconnected from any power sources. Doing this will eliminate any electrical hazards while working on the device.
  • Orient the laptop open to see the keyboard. Have the screen tilted all of the way back for easier access as shown.

Orient the laptop open to see the keyboard. Have the screen tilted all of the way back for easier access as shown.

Step 5

  • Above the keyboard, locate the plastic part containing the power button along with various other command buttons. This needs to come off before you can access the keyboard.
  • Use the spudger to assist in this step. Using the spudger, wedge it underneath the component.
  • Once spudger is inserted and pulled far enough, grasp it and firmly, but carefully, pull it out from the left side first

Above the keyboard, locate the plastic part containing the power button along with various other command buttons. This needs to come off before you can access the keyboard.

Use the spudger to assist in this step. Using the spudger, wedge it underneath the component.

Once spudger is inserted and pulled far enough, grasp it and firmly, but carefully, pull it out from the left side first

Step 6

  • Once unattached from left side, proceed to right side of component and remove it from clips it is attached to.
  • Once removed from clamps, the part is now removed to provide access to the keyboard.

Once unattached from left side, proceed to right side of component and remove it from clips it is attached to.

Once removed from clamps, the part is now removed to provide access to the keyboard.

Step 7

  • The two J0 screws have now become visible. Using the Phillips J0 screwdriver, remove screws. The screws are 5mm long J0 Philips screws.

The two J0 screws have now become visible. Using the Phillips J0 screwdriver, remove screws. The screws are 5mm long J0 Philips screws.

Step 8

  • Once screws are removed, firmly grasp the top edge of the keyboard and wiggle it slightly while firmly tugging on it. This will release the clips holding it.
  • Once clips become unattached, the keyboard is now out.

Once screws are removed, firmly grasp the top edge of the keyboard and wiggle it slightly while firmly tugging on it. This will release the clips holding it.

Once clips become unattached, the keyboard is now out.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Kyle Owen

Member since: 03/21/2018

221 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       UMass Dartmouth, Team S5-G4, Peak Spring 2018                        

                                                  Member of UMass Dartmouth, Team S5-G4, Peak Spring 2018 



                    UMASSD-PEAK-S18S5G4                     


                                            3 Members                     


                                            12 Guides authored