Difficulty

Moderate

Steps

9

Time Required

                          10 minutes

Sections

3

  • Battery
  • 2 steps
  • Hard Drive
  • 4 steps
  • Keyboard
  • 3 steps

Flags

0

  • BackGateway NE56R27u

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Using the spudger, push the orange tab to the unlock position.

Using the spudger, push the orange tab to the unlock position.

1024

Step 2

  • Lift the battery from its compartment.
  • When reinstalling, insert back end of battery first, then clicking into place.

Lift the battery from its compartment.

When reinstalling, insert back end of battery first, then clicking into place.

Step 3

              Hard Drive
  • Unscrew the two 7.9mm Phillips #0 screws that secure the service cover.

Unscrew the two 7.9mm Phillips #0 screws that secure the service cover.

Step 4

  • Use the opening tool to gently pry open the compartment covering.

Use the opening tool to gently pry open the compartment covering.

Step 5

  • Unscrew the two 0.5mm screws from the hard drive brackets using the Phillips #0 screwdriver.
  • Pull the plastic tab attached to the hard drive to the right to remove the hard drive.
  • The hard drive plugs into the port on the left within the compartment. Be sure to gently remove the hard drive without damaging the port.

Unscrew the two 0.5mm screws from the hard drive brackets using the Phillips #0 screwdriver.

Pull the plastic tab attached to the hard drive to the right to remove the hard drive.

The hard drive plugs into the port on the left within the compartment. Be sure to gently remove the hard drive without damaging the port.

Step 6

  • Remove the hard drive by lifting up the right side, releasing the hard drive from the compartment clips on the left.

Remove the hard drive by lifting up the right side, releasing the hard drive from the compartment clips on the left.

Step 7

              Keyboard
  • Flip your laptop over to view the keyboard.
  • Using the spudger, push in the ten tabs at the edges of the keyboard.

Flip your laptop over to view the keyboard.

Using the spudger, push in the ten tabs at the edges of the keyboard.

Step 8

  • Using the opening pick, lift the edges of the keyboard.
  • Repeat around the edges of the device.
  • Lift up the keyboard to expose the cables underneath.

Using the opening pick, lift the edges of the keyboard.

Repeat around the edges of the device.

Lift up the keyboard to expose the cables underneath.

Step 9

  • Release the clamp holding the mini-DIN cord by lifting the two black tabs on either side.
  • Gently pull the mini-DIN cord out of the clamp.
  • Remove the keyboard.

Release the clamp holding the mini-DIN cord by lifting the two black tabs on either side.

Gently pull the mini-DIN cord out of the clamp.

Remove the keyboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Piper Moeller

Member since: 01/24/2020

613 Reputation

                                      4 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Embry-Riddle Aeronautical University, Team S6-G2, Watkins Spring 2020                        

                                                  Member of Embry-Riddle Aeronautical University, Team S6-G2, Watkins Spring 2020 



                    ERAU-WATKINS-S20S6G2                     


                                            4 Members                     


                                            10 Guides authored