Gateway Ne51006U Lcd Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          25 minutes

Sections

Battery
2 steps
Hard Drive
5 steps
LCD Screen
8 steps

Flags

BackGateway NE51006u
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Battery

Make sure your device is powered off before beginning this guide.
Place your device on your workspace, screen facing down. Take the Spudger and use the pointed end to catch the latch below the battery. Drag the latch to the right until the battery detaches from the body of the device.

Make sure your device is powered off before beginning this guide.

Place your device on your workspace, screen facing down. Take the Spudger and use the pointed end to catch the latch below the battery. Drag the latch to the right until the battery detaches from the body of the device.

1024

Step 2

Pull the battery out, making sure to pull the battery parallel to the device.

Pull the battery out, making sure to pull the battery parallel to the device.

Step 3

              Hard Drive

Ensure device is powered off and unplugged from a power source. Place the device upside down.

Ensure device is powered off and unplugged from a power source. Place the device upside down.

Step 4

Use a PH0 Phillips head screwdriver to remove the 9.0 mm screw on the rectangular panel underneath the device.

Use a PH0 Phillips head screwdriver to remove the 9.0 mm screw on the rectangular panel underneath the device.

Step 5

Use a plastic opening tool to pry open the rectangular panel the 9.0 mm screw was removed from.

Use a plastic opening tool to pry open the rectangular panel the 9.0 mm screw was removed from.

Step 6

Remove a single 9.0 mm screw on the silver box containing the hard drive. Pull the plastic flap at the side opposite to the side of the screw housing back in order to remove the silver box containing the hard drive.

Remove a single 9.0 mm screw on the silver box containing the hard drive. Pull the plastic flap at the side opposite to the side of the screw housing back in order to remove the silver box containing the hard drive.

Step 7

Remove the two 9.0 mm screws on each side of the silver box to slide the hard drive from the silver box housing.

Remove the two 9.0 mm screws on each side of the silver box to slide the hard drive from the silver box housing.

Step 8

              LCD Screen

Make sure your device is powered off before beginning this guide.
Remove the black screw covers covering the 4.2 mm screws located inside of the cylindrical hinges at the bottom corners of the screen housing, then use a PH0 Philips head screwdriver to unscrew them.

Remove the black screw covers covering the 4.2 mm screws located inside of the cylindrical hinges at the bottom corners of the screen housing, then use a PH0 Philips head screwdriver to unscrew them.

Step 9

Prior to completing the steps laid out in this guide, it is imperative that the user remove the battery and hard drive via the battery and hard drive replacement guide steps available.
Use a PH0 Philips head screwdriver to remove the remaining 9.0 mm screws on the back of the device which should be sixteen screw in total.

Prior to completing the steps laid out in this guide, it is imperative that the user remove the battery and hard drive via the battery and hard drive replacement guide steps available.

Use a PH0 Philips head screwdriver to remove the remaining 9.0 mm screws on the back of the device which should be sixteen screw in total.

Step 10

Open the laptop and use a plastic opening tool to pry open the sides of the laptop base starting closest to the hinges. Continue doing this until the laptop base is separate from the keyboard.

Open the laptop and use a plastic opening tool to pry open the sides of the laptop base starting closest to the hinges. Continue doing this until the laptop base is separate from the keyboard.

Step 11

After prying the keyboard unit off of the base, Lift the white, hinged covers connected to the three ribbons shown and pull gently to disconnect.
When putting the laptop back together, lift the hinged covers and connect the ribbons before dropping the hinged covers back down.

After prying the keyboard unit off of the base, Lift the white, hinged covers connected to the three ribbons shown and pull gently to disconnect.

When putting the laptop back together, lift the hinged covers and connect the ribbons before dropping the hinged covers back down.

Step 12

Use a plastic opening tool or spudger to remove the plastic frame around the LCD screen. Do this by pressing the wedge in between the crease found in between the two halves of the screen casing.
You will hear a soft click and feel the connection between the two points break as you run the tool around the sides of screen casing.

Use a plastic opening tool or spudger to remove the plastic frame around the LCD screen. Do this by pressing the wedge in between the crease found in between the two halves of the screen casing.

You will hear a soft click and feel the connection between the two points break as you run the tool around the sides of screen casing.

Step 13

Unplug the black cable connected to the webcam above the LCD screen.

Unplug the black cable connected to the webcam above the LCD screen.

Step 14

Use a PH0 Phillips head to remove four 3.4mm black screws. Remove the screen from the casing before moving on to the next step.

Use a PH0 Phillips head to remove four 3.4mm black screws. Remove the screen from the casing before moving on to the next step.

Step 15

Peel the tape off the cable connected to the back of the LCD screen and unplug the cable which is connected to the bottom. The screen should now be fully removed from the laptop casing.

Peel the tape off the cable connected to the back of the LCD screen and unplug the cable which is connected to the bottom. The screen should now be fully removed from the laptop casing.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 2 other contributors

                    Omer Tunagur

Member since: 01/29/2018

423 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       University of Alabama, Team S2-G8, Bedsole Spring 2018                        

                                                  Member of University of Alabama, Team S2-G8, Bedsole Spring 2018 



                    UA-BEDSOLE-S18S2G8                     


                                            4 Members                     


                                            10 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team