Gateway Kav60 Lt2016U Webcam Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

Suggest a time??

Sections

4

• Battery
• 1 step
• Upper Cover
• 5 steps
• LCD
• 4 steps
• Webcam
• 1 step

Flags

2

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

• BackGateway KAV60 LT2016U

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Unlock the tab located in the top left corner of the netbook.
• The red tab indicated that the battery has been properly unlocked.
• Remove the battery.
• When working with electronics, it is always wise to remove the power source before taking the device apart.

Unlock the tab located in the top left corner of the netbook.

The red tab indicated that the battery has been properly unlocked.

Remove the battery.

When working with electronics, it is always wise to remove the power source before taking the device apart.

1024

Step 2

              Upper Cover               

• Make sure the RAM, hard drive, and WiFi card have been removed from the computer before trying to take off the cover so they are not damaged in the process.

Make sure the RAM, hard drive, and WiFi card have been removed from the computer before trying to take off the cover so they are not damaged in the process.

Step 3

• Remove six (6) 5mm screws, two (2) 17.5mm screws, and three (3) 2.5mm screws from the back, using the Phillips #0 screwdriver, as marked here.

Remove six (6) 5mm screws, two (2) 17.5mm screws, and three (3) 2.5mm screws from the back, using the Phillips #0 screwdriver, as marked here.

Step 4

• Pry up the keyboard using a spudger or plastic opening tool in the exact location shown in the photograph.
• Don’t use a screwdriver as a pry tool as shown in this example.
• Carefully disconnect the keyboard ribbon cable from the motherboard, and remove the keyboard.

Pry up the keyboard using a spudger or plastic opening tool in the exact location shown in the photograph.

Don’t use a screwdriver as a pry tool as shown in this example.

Carefully disconnect the keyboard ribbon cable from the motherboard, and remove the keyboard.

Step 5

• Remove the five (5) 5mm screws shown here using the Phillips #0 screwdriver.

Remove the five (5) 5mm screws shown here using the Phillips #0 screwdriver.

Step 6

• Separate the upper cover from the back cover. It is possible to do this without a tool, but you may also use a plastic opening tool for added leverage.
• Be careful to keep even pressure all the way around the cover so that it is not bent beyond repair.
• Carefully disconnect two ribbon cables to complete the separation of the upper cover.

Separate the upper cover from the back cover. It is possible to do this without a tool, but you may also use a plastic opening tool for added leverage.

Be careful to keep even pressure all the way around the cover so that it is not bent beyond repair.

Carefully disconnect two ribbon cables to complete the separation of the upper cover.

Step 7

              LCD               

• Pry the border around the monitor off of the top cover using a plastic opening tool, as shown.
• Be careful not to damage the computer screen in the process

Pry the border around the monitor off of the top cover using a plastic opening tool, as shown.

Be careful not to damage the computer screen in the process

Step 8

• Separate the monitor from the border cover once all snap connections have been pried apart.

Separate the monitor from the border cover once all snap connections have been pried apart.

Step 9

• Remove the six (6) 5mm screws shown here using the Phillips #0 screwdriver.

Remove the six (6) 5mm screws shown here using the Phillips #0 screwdriver.

Step 10

• Take the screen out of the top cover.

Take the screen out of the top cover.

Step 11

              Webcam               

• The webcam is located here, as shown.
• Disconnect the webcam from the wires attaching it to the computer.
• Lift the webcam away from the top cover.

The webcam is located here, as shown.

Disconnect the webcam from the wires attaching it to the computer.

Lift the webcam away from the top cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 6 other contributors 

                    Lydia Benjock                     

Member since: 10/18/2013

1,216 Reputation

                                      10 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Clemson, Team 14-3, Benson Fall 2013                        

                                                  Member of Clemson, Team 14-3, Benson Fall 2013 



                    CLEM-BENSON-F13S14G3                     


                                            3 Members                     


                                            22 Guides authored