Difficulty

Moderate

Steps

10

Time Required

                          5 - 10 minutes

Sections

2

  • Outer Casing
  • 5 steps
  • Screen
  • 5 steps

Flags

3

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

Missed a Step

Oops! This guide is currently missing some important steps.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackGarmin StreetPilot c330

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Outer Casing
  • At the top of the outer frame, insert the plastic spudger into the groove in the center.
  • Lever the frame gently until it pops out of the case.

At the top of the outer frame, insert the plastic spudger into the groove in the center.

Lever the frame gently until it pops out of the case.

1024

Step 2

  • Use a Phillips #00 screwdriver to remove the four screws around the screen.

Use a Phillips #00 screwdriver to remove the four screws around the screen.

Step 3

  • Gently pull from both ends of the casing to separate the front and back panels.
  • Do not force the pieces apart wider than the length of the connecting wires, or you will damage the wiring.

Gently pull from both ends of the casing to separate the front and back panels.

Do not force the pieces apart wider than the length of the connecting wires, or you will damage the wiring.

Step 4

  • Gently unplug the white cable connector using either your fingers or tweezers.

Gently unplug the white cable connector using either your fingers or tweezers.

Step 5

  • Carefully expose both halves of the device.
  • Be sure not to pull the two halves apart further than the black wire can reach.

Carefully expose both halves of the device.

Be sure not to pull the two halves apart further than the black wire can reach.

Step 6

              Screen
  • Remove the three screws holding the motherboard in place.

Remove the three screws holding the motherboard in place.

Step 7

  • Use the spudger to lift up the motherboard.

Use the spudger to lift up the motherboard.

Step 8

  • To remove the ribbon cable, lift the black latch using the spudger tool.
  • Separate the connection using either your fingers, tweezers, or the spudger.

To remove the ribbon cable, lift the black latch using the spudger tool.

Separate the connection using either your fingers, tweezers, or the spudger.

Step 9

  • Slide the spudger under the two flexible tabs located on the right and left sides of the bottom of the screen.
  • Rotate the spudger outward until the tabs are no longer holding the screen.
  • When reassembling, slide the bottom of the screen under the two permanent tabs.
  • Push the screen out from the front.

Slide the spudger under the two flexible tabs located on the right and left sides of the bottom of the screen.

Rotate the spudger outward until the tabs are no longer holding the screen.

When reassembling, slide the bottom of the screen under the two permanent tabs.

Push the screen out from the front.

Step 10

  • Separate the screen from the front cover.

Separate the screen from the front cover.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 9 other contributors 


                    Adrian Leon

Member since: 10/07/2010

173 Reputation

                                      3 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       Cal Poly, Team 22-1, Maness Fall 2010                        

                                                  Member of Cal Poly, Team 22-1, Maness Fall 2010 



                    CPSU-MANESS-F10S22G1                     


                                            3 Members                     


                                            4 Guides authored