Garmin N Vi 52Lm Lcd And Digitizer Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          7 - 10 minutes

Sections

Garmin Nüvi 52LM Disassembly
2 steps
Battery
3 steps
LCD and Digitizer
2 steps

Flags

BackGarmin Nüvi 52LM
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Garmin Nüvi 52LM Disassembly

Place the device face-down, with the screen facing the surface. There are 8.7mm screws located in each of the back 4 corners of the device. Using a T5 Torx screw bit, unscrew all four screws and leave them aside.

Place the device face-down, with the screen facing the surface. There are 8.7mm screws located in each of the back 4 corners of the device. Using a T5 Torx screw bit, unscrew all four screws and leave them aside.

1024

Step 2

Place a plastic opening tool in the seam between the back and front plates of the device. Using constant pressure, slowly and continuously slide the tool along the seam. The tool should disable each of the hooks holding the two plates together. If unsuccessful, apply slightly more pressure and try again.
Once all hooks are disabled, slowly separate the two plates, being careful not to damage the ribbon wire still connecting the two.

Place a plastic opening tool in the seam between the back and front plates of the device. Using constant pressure, slowly and continuously slide the tool along the seam. The tool should disable each of the hooks holding the two plates together. If unsuccessful, apply slightly more pressure and try again.

Once all hooks are disabled, slowly separate the two plates, being careful not to damage the ribbon wire still connecting the two.

Step 3

              Battery

Using the T5 Torx screwdriver, unscrew the two 5.6mm screws at the top right and bottom right corners of the motherboard.

Using the T5 Torx screwdriver, unscrew the two 5.6mm screws at the top right and bottom right corners of the motherboard.

Step 4

Gently unplug the wire connecting the battery to the small socket on the back of the motherboard.

Gently unplug the wire connecting the battery to the small socket on the back of the motherboard.

Step 5

Using a plastic opening tool, pry the battery from the back cover of the device. There may be an adhesive sticker keeping it in place, so you may need to apply some force.
The battery should now be completely detached from the other parts.

Using a plastic opening tool, pry the battery from the back cover of the device. There may be an adhesive sticker keeping it in place, so you may need to apply some force.

The battery should now be completely detached from the other parts.

Step 6

              LCD and Digitizer

On the motherboard, lift the small plate that holds the orange ribbon wire in place.
Gently disconnect the ribbon wire from its connection to the motherboard.

On the motherboard, lift the small plate that holds the orange ribbon wire in place.

Gently disconnect the ribbon wire from its connection to the motherboard.

Step 7

Using a moderate amount of force, pull each of the triangular hooks holding the screen in place away.
Once all of the triangular hooks are off of the screen, slide the device out of the case, pulling away from the rectangular hooks at the bottom.
The screen and digitizer should now be completely detached from the other parts of the device, and a new one can now be placed.

Using a moderate amount of force, pull each of the triangular hooks holding the screen in place away.

Once all of the triangular hooks are off of the screen, slide the device out of the case, pulling away from the rectangular hooks at the bottom.

The screen and digitizer should now be completely detached from the other parts of the device, and a new one can now be placed.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Blaine Francis

Member since: 01/24/2017

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Cal Poly, Team 10-1, Banghart Winter 2017                        

                                                  Member of Cal Poly, Team 10-1, Banghart Winter 2017 



                    CPSU-BANGHART-W17S10G1                     


                                            4 Members                     


                                            5 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team