Garmin N Vi 3590 Lmt Glass Screen Replacement Repair Guide

Difficulty

Moderate

Steps

11

Time Required

                          15 - 30 minutes            

Sections

2

• Battery
• 5 steps
• Glass Screen
• 6 steps

Flags

0

• BackGarmin nüvi 3590 LMT

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Battery               

• Turn the device off by pressing and holding the power button on the top left of the device.

Turn the device off by pressing and holding the power button on the top left of the device.

1024

Step 2

• Use the plastic opening tool to separate the tabs on the black back cover of the device by leveraging the tool against the frame around the perimeter of the device.

Use the plastic opening tool to separate the tabs on the black back cover of the device by leveraging the tool against the frame around the perimeter of the device.

Step 3

• Once all of the tabs are popped out, take the back cover off.
• The back cover is a separate piece from the device.

Once all of the tabs are popped out, take the back cover off.

The back cover is a separate piece from the device.

Step 4

• Using the plastic spudger, carefully remove the white tab connected to the battery from the device by pulling the tab in the opposite direction from which it is connected.

Using the plastic spudger, carefully remove the white tab connected to the battery from the device by pulling the tab in the opposite direction from which it is connected.

Step 5

• Use the plastic spudger to lift the battery up and away from the device.
• Do not puncture or bend the battery. Serious health complications could occur.

Use the plastic spudger to lift the battery up and away from the device.

Do not puncture or bend the battery. Serious health complications could occur.

Step 6

              Glass Screen               

• Using the T5 bit, unscrew the four 5.7mm screws in the four corners on the back of the device.

Using the T5 bit, unscrew the four 5.7mm screws in the four corners on the back of the device.

Step 7

• Use the plastic opening tool to leverage up on the tabs between the black screen and the metal frame.
• Do not forcibly separate the two pieces after the tabs have been popped. There are connections between the two pieces that could be torn.

Use the plastic opening tool to leverage up on the tabs between the black screen and the metal frame.

Do not forcibly separate the two pieces after the tabs have been popped. There are connections between the two pieces that could be torn.

Step 8

• Using your fingers, pull up on the red and black wire from the back of the screen.
• This wire is part of the speaker, so be careful not to damage it.

Using your fingers, pull up on the red and black wire from the back of the screen.

This wire is part of the speaker, so be careful not to damage it.

Step 9

• Pull up on the smaller orange tab with your finger from the circuit board.

Pull up on the smaller orange tab with your finger from the circuit board.

Step 10

• For the larger orange connection, there is a white tab holding the connection to the circuit board.
• Lift the white tab gently with the plastic spudger and remove the orange connection from the circuit board.

For the larger orange connection, there is a white tab holding the connection to the circuit board.

Lift the white tab gently with the plastic spudger and remove the orange connection from the circuit board.

Step 11

• Use the metal spudger to leverage and lift the metal board from the glass paneling around the perimeter of the device.
• Be careful to not damage any connections.

Use the metal spudger to leverage and lift the metal board from the glass paneling around the perimeter of the device.

Be careful to not damage any connections.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      6 other people completed this guide.                                             

Author

                                      with 3 other contributors 

                    Kayla Katz                     

Member since: 03/11/2015

576 Reputation

                                      2 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Colorado Springs, Team 4-1, Panko Spring 2015                        

                                                  Member of Colorado Springs, Team 4-1, Panko Spring 2015 



                    UCCS-PANKO-S15S4G1                     


                                            2 Members                     


                                            5 Guides authored                     

Bryan - Nov 30, 2015

Reply

Where can I buy the glass screen digitizer?

Dennis Kiel - Jan 13, 2019

Reply

Thanks for instruction, it helped me a lot, but removing of battery in step 5 makes no sense. The battery stays on the metal plate and does not disturbs for next steps. Of course the cable must be disconnected from the board to make it powerless.

BR

Dennis