Difficulty
Moderate
Steps
10
Time Required
30 minutes
Sections
2
- Back Cover and AA Batteries
- 3 steps
- Screen
- 7 steps
Flags
0
BackGarmin GPSmap 60CSx
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover and AA Batteries
- Lift and twist the battery cover release 90 degrees counterclockwise on the back of the device.
Lift and twist the battery cover release 90 degrees counterclockwise on the back of the device.
1024
Step 2
- Lift battery release up to remove battery cover.
Lift battery release up to remove battery cover.
Step 3
- Pull AA batteries out.
Pull AA batteries out.
Step 4
Screen
- Remove the six 10 mm screws on the back of the device with a Phillips #0 Screwdriver.
- Flip the back panel over to view the green electronics board (the PCB) and the PCB cover.
- Remove the black, yellow, blue, and red wires connected to the PCB with light force.
Remove the six 10 mm screws on the back of the device with a Phillips #0 Screwdriver.
Flip the back panel over to view the green electronics board (the PCB) and the PCB cover.
Remove the black, yellow, blue, and red wires connected to the PCB with light force.
Step 5
- Take the spudger and place it in the bottom right corner of the black PCB cover.
- Use the spudger to pry the corner out. This will need to be done to all four corners of the PCB cover.
- It is best to do remove the bottom corners first.
- Pull the PCB cover out of the GPSMap 60CSx.
Take the spudger and place it in the bottom right corner of the black PCB cover.
Use the spudger to pry the corner out. This will need to be done to all four corners of the PCB cover.
It is best to do remove the bottom corners first.
Pull the PCB cover out of the GPSMap 60CSx.
Step 6
- Carefully use the spudger to lift the PCB a few centimeters.
- Pull the PCB towards the bottom of the GPSMap 60CSx.
- This will pull the other components out of the GPSMap 60CSx like the antenna and the screen.
Carefully use the spudger to lift the PCB a few centimeters.
Pull the PCB towards the bottom of the GPSMap 60CSx.
This will pull the other components out of the GPSMap 60CSx like the antenna and the screen.
Step 7
- Apply light pressure to the four white tabs that are holding the screen in place.
- The screen will now come off the PCB.
Apply light pressure to the four white tabs that are holding the screen in place.
The screen will now come off the PCB.
Step 8
- Turn the PCB over so the screen connector is facing you.
- Move the screen out of the way for access to the screen connector.
Turn the PCB over so the screen connector is facing you.
Move the screen out of the way for access to the screen connector.
Step 9
- Use tweezers to pull the two white pins on the connector forward.
Use tweezers to pull the two white pins on the connector forward.
Step 10
- Remove the screen ribbon connector and screen.
Remove the screen ribbon connector and screen.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
4 other people completed this guide.
Author
with 5 other contributors
Thomas Humphrey
Member since: 04/05/2018
537 Reputation
4 Guides authored
Badges:
9
+6 more badges
Team
Linn Benton Community College, Team S2-G5, Johnson Spring 2018
Member of Linn Benton Community College, Team S2-G5, Johnson Spring 2018
LBCC-JOHNSON-S18S2G5
5 Members
5 Guides authored
salvador2707 - Jul 7, 2018
Reply
i have a 60csx and the battery bounces the liquid, can help me?
jlciscorp - Jan 9, 2020
Reply
Thank you for these step by step detailed instructions.
