Difficulty

Moderate

Steps

12

Time Required

                          7 minutes

Sections

2

  • Back Cover
  • 5 steps
  • Treat Guide Chamber
  • 7 steps

Flags

1

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

  • BackFurbo Dog Camera

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Back Cover
  • Remove the lid from the top of your Furbo Dog Camera.

Remove the lid from the top of your Furbo Dog Camera.

1024

Step 2

  • Rotate your Furbo so that the bottom faces you.
  • Remove the rubber caps to reveal the four screws on the bottom of the Furbo.

Rotate your Furbo so that the bottom faces you.

Remove the rubber caps to reveal the four screws on the bottom of the Furbo.

Step 3

  • Use a 2.5 mm Flathead screwdriver to remove the four 5 mm screws from the bottom of the Furbo.
  • Use a 2.5 mm Flathead screwdriver to remove the single 5 mm screw under the silver sticker.

Use a 2.5 mm Flathead screwdriver to remove the four 5 mm screws from the bottom of the Furbo.

Use a 2.5 mm Flathead screwdriver to remove the single 5 mm screw under the silver sticker.

Step 4

  • Rotate your Furbo so that the side is facing towards you.
  • Use an opening tool to separate the two plastic coverings.

Rotate your Furbo so that the side is facing towards you.

Use an opening tool to separate the two plastic coverings.

Step 5

  • Once you have separated the two plastic coverings, remove one side by pulling on it and carefully separating it from the adhesive.

Once you have separated the two plastic coverings, remove one side by pulling on it and carefully separating it from the adhesive.

Step 6

              Treat Guide Chamber
  • Use a Phillips #000 screwdriver to remove the two small 3 mm black screws on either side of the plastic hinge.
  • After removing the two screws, carefully pull off the plastic hinge.

Use a Phillips #000 screwdriver to remove the two small 3 mm black screws on either side of the plastic hinge.

After removing the two screws, carefully pull off the plastic hinge.

Step 7

  • Locate each end of the treat chamber door where the white plastic hook is latched behind the metal rod, and carefully unlatch the entire white plastic piece from the metal rod on both sides.

Locate each end of the treat chamber door where the white plastic hook is latched behind the metal rod, and carefully unlatch the entire white plastic piece from the metal rod on both sides.

Step 8

  • Use a Phillips #000 screwdriver to remove the two 5 mm screws above the treat dispensing door.

Use a Phillips #000 screwdriver to remove the two 5 mm screws above the treat dispensing door.

Step 9

  • Lift up the treat dispensing door, and use a Phillips #000 screwdriver to remove the two 5 mm screws at the bottom of the dispensing hole.

Lift up the treat dispensing door, and use a Phillips #000 screwdriver to remove the two 5 mm screws at the bottom of the dispensing hole.

Step 10

  • Carefully pull off the treat dispensing chamber with your hands and set it aside.
  • the treat dispensing chamber is the curved white plastic tube below the treat dispensing door.

Carefully pull off the treat dispensing chamber with your hands and set it aside.

the treat dispensing chamber is the curved white plastic tube below the treat dispensing door.

Step 11

  • Lift the treat chamber door, and carefully pull the treat guide chamber free.
  • This is the circular plastic piece that rests behind the treat dispensing door.

Lift the treat chamber door, and carefully pull the treat guide chamber free.

This is the circular plastic piece that rests behind the treat dispensing door.

Step 12

  • Now that both your treat guide chamber and treat dispensing chamber have been removed, you can stick your finger into the launching mechanism to dislodge any jammed treats.

Now that both your treat guide chamber and treat dispensing chamber have been removed, you can stick your finger into the launching mechanism to dislodge any jammed treats.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Susan McLaughlin

Member since: 03/21/2022

195 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       University of Alabama, Team 1-1, Bedsole Spring 2022                        

                                                  Member of University of Alabama, Team 1-1, Bedsole Spring 2022 



                    UA-BEDSOLE-S22S1G1                     


                                            3 Members                     


                                            6 Guides authored