Difficulty
Moderate
Steps
17
Time Required
15 minutes
Sections
4
- Back Case
- 3 steps
- Inner Back Shield
- 4 steps
- Battery
- 4 steps
- Motherboard
- 6 steps
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackFujitsu Lifebook Stylistic Q584
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Case
- Remove the white sticker covering the screws (if applicable).
- Use the PH1 screwdriver to remove the four 2 mm screws from the the backside of the device.
Remove the white sticker covering the screws (if applicable).
Use the PH1 screwdriver to remove the four 2 mm screws from the the backside of the device.
1024
Step 2
- Insert the plastic opening tool along the seam of the back case.
- Gently slide the plastic opening tool along the entire seam popping the clips free.
Insert the plastic opening tool along the seam of the back case.
Gently slide the plastic opening tool along the entire seam popping the clips free.
Step 3
- Carefully lift the back case and remove the smartcard ribbon from the motherboard.
Carefully lift the back case and remove the smartcard ribbon from the motherboard.
Step 4
Inner Back Shield
- Remove the ten 3mm screws with a PH00 screwdriver from the shield.
Remove the ten 3mm screws with a PH00 screwdriver from the shield.
Step 5
- Remove the grey docking station port cover.
Remove the grey docking station port cover.
Step 6
- Gently slide the plastic opening tool along the entire seam popping the clips free.
Step 7
- Lift the shield away from the device and remove the fingerprint scanner’s ribbon from the motherboard.
Lift the shield away from the device and remove the fingerprint scanner’s ribbon from the motherboard.
Step 8
Battery
- Pull up the cord that connects the battery to the motherboard
Pull up the cord that connects the battery to the motherboard
Step 9
- Remove seven 1mm screws using a PH00 screwdriver.
Remove seven 1mm screws using a PH00 screwdriver.
Step 10
- Disconnect upper peripheral ribbons from motherboard.
- Disconnect left peripheral ribbon from motherboard.
Disconnect upper peripheral ribbons from motherboard.
Disconnect left peripheral ribbon from motherboard.
Step 11
- Gently lift the battery from the casing.
Gently lift the battery from the casing.
Step 12
Motherboard
- Remove three 3mm screws using a PH00 screwdriver.
Remove three 3mm screws using a PH00 screwdriver.
Step 13
- Remove all of the ribbon connector cables from the motherboard using an ESD-safe spudger.
Remove all of the ribbon connector cables from the motherboard using an ESD-safe spudger.
Step 14
- Gently pry up the motherboard.
Gently pry up the motherboard.
Step 15
- Gently lift the foil tape under the motherboard to reveal the connector.
Gently lift the foil tape under the motherboard to reveal the connector.
Step 16
- Remove the clip holding in the connector with an ESD-safe spudger.
Remove the clip holding in the connector with an ESD-safe spudger.
Step 17
- Remove the connector with an ESD-safe spudger.
Remove the connector with an ESD-safe spudger.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 4 other contributors
Casey
Member since: 03/25/2019
256 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
IUPUI, Team S1-G1, Henning Spring 2019
Member of IUPUI, Team S1-G1, Henning Spring 2019
IUPUI-HENNING-S19S1G1
3 Members
3 Guides authored
net ho - Jul 8, 2021
Reply
step16, that metal clip is supposed to be lifted up, not departed away
