Difficulty
Moderate
Steps
16
Time Required
10 minutes
Sections
4
- Back Case
- 3 steps
- Inner Back Shield
- 4 steps
- Battery
- 4 steps
- Headphone Jack
- 5 steps
Flags
1
Action Shots
Be an action hero! This guide needs images that better demonstrate how to perform specific actions.
BackFujitsu Lifebook Stylistic Q584
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Case
- Remove the white sticker covering the screws (if applicable).
- Use the PH1 screwdriver to remove the four 2 mm screws from the the backside of the device.
Remove the white sticker covering the screws (if applicable).
Use the PH1 screwdriver to remove the four 2 mm screws from the the backside of the device.
1024
Step 2
- Insert the plastic opening tool along the seam of the back case.
- Gently slide the plastic opening tool along the entire seam popping the clips free.
Insert the plastic opening tool along the seam of the back case.
Gently slide the plastic opening tool along the entire seam popping the clips free.
Step 3
- Carefully lift the back case and remove the smartcard ribbon from the motherboard.
Carefully lift the back case and remove the smartcard ribbon from the motherboard.
Step 4
Inner Back Shield
- Remove the ten 3mm screws with a PH00 screwdriver from the shield.
Remove the ten 3mm screws with a PH00 screwdriver from the shield.
Step 5
- Remove the grey docking station port cover.
Remove the grey docking station port cover.
Step 6
- Gently slide the plastic opening tool along the entire seam popping the clips free.
Step 7
- Lift the shield away from the device and remove the fingerprint scanner’s ribbon from the motherboard.
Lift the shield away from the device and remove the fingerprint scanner’s ribbon from the motherboard.
Step 8
Battery
- Pull up the cord that connects the battery to the motherboard
Pull up the cord that connects the battery to the motherboard
Step 9
- Remove seven 1mm screws using a PH00 screwdriver.
Remove seven 1mm screws using a PH00 screwdriver.
Step 10
- Disconnect upper peripheral ribbons from motherboard.
- Disconnect left peripheral ribbon from motherboard.
Disconnect upper peripheral ribbons from motherboard.
Disconnect left peripheral ribbon from motherboard.
Step 11
- Gently lift the battery from the casing.
Gently lift the battery from the casing.
Step 12
Headphone Jack
- Remove the two 0.2 mm screws with a PH00 Screwdriver.
Remove the two 0.2 mm screws with a PH00 Screwdriver.
Step 13
- Remove the two 0.2 mm screws with a PH00 screwdriver
Remove the two 0.2 mm screws with a PH00 screwdriver
Step 14
- Now use an ESD-safe spudger to gently pry up the silver piece and flip it over. Be sure not to remove this piece completely!
Now use an ESD-safe spudger to gently pry up the silver piece and flip it over. Be sure not to remove this piece completely!
Step 15
- Use an ESD-safe spudger to gently push the yellow piece out from the white cradle.
Use an ESD-safe spudger to gently push the yellow piece out from the white cradle.
Step 16
- When removing the headphone jack, simply use your fingers to pull out the white and black piece altogether.
When removing the headphone jack, simply use your fingers to pull out the white and black piece altogether.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 4 other contributors
Briana Cockerham
Member since: 03/26/2019
127 Reputation
1 Guide authored
Badges:
3
Team
IUPUI, Team S1-G1, Henning Spring 2019
Member of IUPUI, Team S1-G1, Henning Spring 2019
IUPUI-HENNING-S19S1G1
3 Members
3 Guides authored
