Difficulty
Moderate
Steps
17
Time Required
5 minutes
Sections
5
- Battery
- 2 steps
- Hinge Cover
- 5 steps
- Keyboard
- 3 steps
- Metal Motherboard Cover
- 2 steps
- Display
- 5 steps
Flags
0
BackFujitsu LifeBook N3510
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Locate the two clips on the bottom of the computer that support the battery.
Locate the two clips on the bottom of the computer that support the battery.
1024
Step 2
- Using your fingers, push the clips inward and then upward.
- Lift the battery out of the computer.
Using your fingers, push the clips inward and then upward.
Lift the battery out of the computer.
Step 3
Hinge Cover
- Use a spudger to lift the back of the hinge cover on the left and right sides of the computer.
Use a spudger to lift the back of the hinge cover on the left and right sides of the computer.
Step 4
- Lay the computer flat on a stable surface with the monitor pointing away from you.
Lay the computer flat on a stable surface with the monitor pointing away from you.
Step 5
- Use a spudger to partially lift the hinge cover.
Use a spudger to partially lift the hinge cover.
Step 6
- The hinge cover has a ribbon cable that is attached to the motherboard. To prevent damage, lift the hinge cover slowly.
- Lift the hinge cover enough to expose the ribbon cable.
The hinge cover has a ribbon cable that is attached to the motherboard. To prevent damage, lift the hinge cover slowly.
Lift the hinge cover enough to expose the ribbon cable.
Step 7
- Disconnect the ribbon cable from the motherboard and remove the hinge cover from the computer.
Disconnect the ribbon cable from the motherboard and remove the hinge cover from the computer.
Step 8
Keyboard
- The keyboard has a ribbon cable that is attached to the motherboard. To prevent damage, lift keyboard slowly.
- Lift the keyboard enough to expose the ribbon cable.
The keyboard has a ribbon cable that is attached to the motherboard. To prevent damage, lift keyboard slowly.
Lift the keyboard enough to expose the ribbon cable.
Step 9
- Use a spudger to release the ribbon cable from the motherboard.
Use a spudger to release the ribbon cable from the motherboard.
Step 10
- After the ribbon has been detached, carefully remove the keyboard.
After the ribbon has been detached, carefully remove the keyboard.
Step 11
Metal Motherboard Cover
- Remove the following screws, all labeled “3.”
- Two 8.63mm screws.
- One 7.65mm screw.
- One 5.74mm screw.
- Remove the following screw, labeled “15.”
- One 17.81mm screw.
Remove the following screws, all labeled “3.”
Two 8.63mm screws.
One 7.65mm screw.
One 5.74mm screw.
Remove the following screw, labeled “15.”
One 17.81mm screw.
Step 12
- Lift the cover with fingers and remove.
Lift the cover with fingers and remove.
Step 13
Display
- Remove labeled screws.
Remove labeled screws.
Step 14
- Remove the screws from the bottom of the hinge as shown in the image.
Remove the screws from the bottom of the hinge as shown in the image.
Step 15
- Use a spudger to detach and remove cables from the motherboard.
Use a spudger to detach and remove cables from the motherboard.
Step 16
- Unplug highlighted cables from the wireless module.
Unplug highlighted cables from the wireless module.
Step 17
- Hold down the body of the computer by placing your hands in the pictured positions. Then, lift the display from the body.
Hold down the body of the computer by placing your hands in the pictured positions. Then, lift the display from the body.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
2 other people completed this guide.
Author
with 10 other contributors
Neil Daniels
Member since: 01/17/2011
1,411 Reputation
11 Guides authored
Badges:
12
+9 more badges
Team
Cal Poly, Team 5-18, Amido Winter 2011
Member of Cal Poly, Team 5-18, Amido Winter 2011
CPSU-AMIDO-W11S5G18
3 Members
22 Guides authored
