Fujifilm Xp20 Rear Case Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

Rear Case
6 steps

Flags

BackFujifilm XP20
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Rear Case

Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera.
Using a Phillips #00 screwdriver, remove the two 3.0 mm screws on the bottom of the front face.

Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera.

Using a Phillips #00 screwdriver, remove the two 3.0 mm screws on the bottom of the front face.

1024

Step 2

Using a Phillips #00 screwdriver, remove the 3.0 mm screws on the bottom of the camera closer to the back.
Using a Phillips #00 screwdriver remove the two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Using a Phillips #00 screwdriver, remove the 3.0 mm screws on the bottom of the camera closer to the back.

Using a Phillips #00 screwdriver remove the two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Step 3

Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.

Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.

Step 4

Using a 1.5mm Hex screwdriver, remove the 3.0 mm hex screw on top edge of silver panel.
Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge.
Once both screws are removed the silver side casing will slide off.

Using a 1.5mm Hex screwdriver, remove the 3.0 mm hex screw on top edge of silver panel.

Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge.

Once both screws are removed the silver side casing will slide off.

Step 5

Unlatch the four clasps located on each side of the camera by hand.
The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.

Unlatch the four clasps located on each side of the camera by hand.

The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.

Step 6

Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws.
Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.
The rear panel is now free from the camera.

Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws.

Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.

The rear panel is now free from the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Stephen Harden

Member since: 10/08/2016

243 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       IUPUI, Team 1-1, Wilson Fall 2016                        

                                                  Member of IUPUI, Team 1-1, Wilson Fall 2016 



                    IUPUI-WILSON-F16S1G1                     


                                            3 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team