Fujifilm Xp20 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

LCD Screen
10 steps

Flags

BackFujifilm XP20
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              LCD Screen

Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera.
Using a Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.

Using a 1.5mm Hex Screwdriver, remove the two 3.0 mm hex screws on the front of the camera.

Using a Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.

1024

Step 2

Using a Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back.
Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Using a Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back.

Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Step 3

Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.

Using a Phillips #00 screwdriver, remove the two 3.0 mm screws.

Step 4

Using a 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel.
Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge.
Once both screws are removed the silver side casing will slide off.

Using a 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel.

Using a Phillips #00 screwdriver, remove the 3.0 mm screw on bottom edge.

Once both screws are removed the silver side casing will slide off.

Step 5

Unlatch the four clasps located on each side of the camera by hand.
The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.

Unlatch the four clasps located on each side of the camera by hand.

The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm XP20 Battery Replacement for instructions.

Step 6

Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws.
Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.
The rear panel is now free from the camera.

Using a Phillips #00 screwdriver, remove the seven 3.0 mm screws.

Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.

The rear panel is now free from the camera.

Step 7

Take the spudger and wedge it in between the screen and the frame.
Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.

Take the spudger and wedge it in between the screen and the frame.

Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.

Step 8

Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame.
Make your way around with the spudger just enough to separate the screen and frame once again.

Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame.

Make your way around with the spudger just enough to separate the screen and frame once again.

Step 9

Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame.
Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.

Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame.

Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.

Step 10

Detach the LCD screen from the motherboard by detaching the orange ribbon.

Detach the LCD screen from the motherboard by detaching the orange ribbon.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors

                    Stephen Harden

Member since: 10/08/2016

243 Reputation

                                      2 Guides authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       IUPUI, Team 1-1, Wilson Fall 2016                        

                                                  Member of IUPUI, Team 1-1, Wilson Fall 2016 



                    IUPUI-WILSON-F16S1G1                     


                                            3 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team