Fujifilm Finepix Z90 Lcd Screen Replacement Repair Guide

Difficulty

Difficult

Steps

Time Required

                          10 - 30 minutes

Sections

LCD Screen
7 steps

Flags

BackFujifilm FinePix Z90
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              LCD Screen

Locate the right side of the camera, where the USB connector is. Remove uncovered Phillips #000 screw.
Once the uncovered screw is removed, open the USB connector cover to remove the next Phillips #000 screw.

Locate the right side of the camera, where the USB connector is. Remove uncovered Phillips #000 screw.

Once the uncovered screw is removed, open the USB connector cover to remove the next Phillips #000 screw.

1024

Step 2

Remove the two uncovered Phillips #000 screws from the left side.
Repeat for the screws on the bottom.

Remove the two uncovered Phillips #000 screws from the left side.

Repeat for the screws on the bottom.

Step 3

Remove the casing from the back of camera where LCD screen is located.
On the right side of the camera locate the wrist strap. Carefully remove the lace that attached wrist strap to camera.
Located just above (or next to) lace that attaches wrist strap is a ribbon cable. Be extremely cautious not to tear when removing lace. This ribbon connects the front panel to the motherboard.
Gently remove silver piece that lace was connected to, set aside.

Remove the casing from the back of camera where LCD screen is located.

On the right side of the camera locate the wrist strap. Carefully remove the lace that attached wrist strap to camera.

Located just above (or next to) lace that attaches wrist strap is a ribbon cable. Be extremely cautious not to tear when removing lace. This ribbon connects the front panel to the motherboard.

Gently remove silver piece that lace was connected to, set aside.

Step 4

After removing silver piece that attached to lace, locate and remove screw.
Turning camera back to the LCD screen, remove the three screws just to the right of screen. These are located next to the ribbon cables attaching the LCD to the motherboard.

After removing silver piece that attached to lace, locate and remove screw.

Turning camera back to the LCD screen, remove the three screws just to the right of screen. These are located next to the ribbon cables attaching the LCD to the motherboard.

Step 5

Gently remove front of camera face (casing).
Once removed motherboard should be displayed. Be very careful with this section.

Gently remove front of camera face (casing).

Once removed motherboard should be displayed. Be very careful with this section.

Step 6

Using a plastic opening tool, pull the LCD screen to the left slightly, lift it and flip it open to the right.
There is another ribbon cable attaching the LCD screen to the motherboard; be careful not to tear it. Be sure to tear black electrical tape before removing ribbon.

Using a plastic opening tool, pull the LCD screen to the left slightly, lift it and flip it open to the right.

There is another ribbon cable attaching the LCD screen to the motherboard; be careful not to tear it. Be sure to tear black electrical tape before removing ribbon.

Step 7

Using a plastic opening tool, flip open the black lever to release the ribbon.
Gently slide the cable out of the lock; the LCD screen is now ready to be removed.

Using a plastic opening tool, flip open the black lever to release the ribbon.

Gently slide the cable out of the lock; the LCD screen is now ready to be removed.

Once you have removed the damaged screen, following the instructions in reverse order will instruct you to reassemble your device.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Sam Clark

Member since: 11/03/2015

301 Reputation

                                      3 Guides authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       UMass Dartmouth, Team 1-6, Bhusal Fall 2015                        

                                                  Member of UMass Dartmouth, Team 1-6, Bhusal Fall 2015 



                    UMASSD-BHUSAL-F15S1G6                     


                                            2 Members                     


                                            6 Guides authored

Introduction#

What you need#

Team#

Introduction

What you need

Team