Difficulty
Difficult
Steps
21
Time Required
45 minutes - 1 hour
Sections
4
- Battery
- 2 steps
- Exterior Case
- 7 steps
- Interior Case
- 5 steps
- Speaker
- 7 steps
Flags
0
BackFujifilm FinePix XP80
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
Please note: this guide requires soldering. For more information, see the Soldering Guide.
What you need
Step 1
Battery
- Open the side panel which houses the battery compartment. Press the center button down and twist the dial.
Open the side panel which houses the battery compartment. Press the center button down and twist the dial.
1024
Step 2
- Release the battery from its secured position by pulling the orange tab back. The battery can then be removed from its compartment.
Release the battery from its secured position by pulling the orange tab back. The battery can then be removed from its compartment.
Step 3
Exterior Case
- Using a Phillips PH000 bit, remove the five 2mm screws on the bottom of the camera.
Using a Phillips PH000 bit, remove the five 2mm screws on the bottom of the camera.
Step 4
- Using a H1.3 hex head bit, remove the two 2mm screws from the top of the camera.
Using a H1.3 hex head bit, remove the two 2mm screws from the top of the camera.
Step 5
- Using a H1.3 hex head bit, remove the two 2mm screws on the side of the camera.
Using a H1.3 hex head bit, remove the two 2mm screws on the side of the camera.
Step 6
- Using a plastic opening tool, gently pry up the edge of the button case, located at the top of the camera, until it unclips.
Using a plastic opening tool, gently pry up the edge of the button case, located at the top of the camera, until it unclips.
Step 7
- Gently pry the side area of the case apart.
Gently pry the side area of the case apart.
Step 8
- Continue using the opening tool on the bottom of the camera to gently pry the case apart.
Continue using the opening tool on the bottom of the camera to gently pry the case apart.
Step 9
- Use the plastic opening tool to carefully pry the yellow front panel completely away from the camera.
- Use your hands to take off the yellow back panel.
Use the plastic opening tool to carefully pry the yellow front panel completely away from the camera.
Use your hands to take off the yellow back panel.
Step 10
Interior Case
- Using the H1.3 hex head bit, remove the four screws on the front of the camera.
Using the H1.3 hex head bit, remove the four screws on the front of the camera.
Step 11
- Using the H1.3 hex head bit, remove the screw on the back of the camera.
Using the H1.3 hex head bit, remove the screw on the back of the camera.
Step 12
- Open the battery compartment on the side of the camera.
- Using your plastic opening tool, carefully pry the two clips apart as indicated in the photo.
Open the battery compartment on the side of the camera.
Using your plastic opening tool, carefully pry the two clips apart as indicated in the photo.
Step 13
- Unclip the front interior panel from the top, bottom and side of the camera.
Unclip the front interior panel from the top, bottom and side of the camera.
Step 14
- Gently open the camera, noting the presence of two orange tapes along one side that connect the motherboard to the LCD screen.
- Open the camera like a book and lay both sides flat next to one another, leaving the orange tapes connected.
Gently open the camera, noting the presence of two orange tapes along one side that connect the motherboard to the LCD screen.
Open the camera like a book and lay both sides flat next to one another, leaving the orange tapes connected.
Step 15
Speaker
- Carefully remove the black sticker covering the motherboard.
Carefully remove the black sticker covering the motherboard.
Step 16
- Using a PH000 Phillips bit, remove the four screws shown.
Using a PH000 Phillips bit, remove the four screws shown.
Step 17
- Using a plastic opening tool, carefully remove the lens housing to the left of the motherboard.
Using a plastic opening tool, carefully remove the lens housing to the left of the motherboard.
Step 18
- Peel back the sticker on the side of the motherboard.
- Using a PH000 Phillips bit, remove the screw.
Peel back the sticker on the side of the motherboard.
Using a PH000 Phillips bit, remove the screw.
Step 19
- Using a PH000 Phillips bit, remove the screw shown.
- Unclip the three ribbon cables that are still attached to the motherboard.
- Use the plastic opening tool to gently pry the motherboard loose.
- Move the motherboard aside slightly to reveal the speaker, which is connected to the motherboard by red and black wires.
Using a PH000 Phillips bit, remove the screw shown.
Unclip the three ribbon cables that are still attached to the motherboard.
Use the plastic opening tool to gently pry the motherboard loose.
Move the motherboard aside slightly to reveal the speaker, which is connected to the motherboard by red and black wires.
Step 20
- Lift the motherboard out of the way, being careful of the speaker wires.
- Carefully pry the speaker out of its slot in the case.
Lift the motherboard out of the way, being careful of the speaker wires.
Carefully pry the speaker out of its slot in the case.
Step 21
- To remove the speaker from the motherboard, desolder its connection.
- For instructions on desoldering, see the following guide: How To Solder and Desolder Connections
To remove the speaker from the motherboard, desolder its connection.
For instructions on desoldering, see the following guide: How To Solder and Desolder Connections
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 6 other contributors
Amanda Lewis
Member since: 09/25/2016
317 Reputation
3 Guides authored
Badges:
11
+8 more badges
Team
USF Tampa, Team 1-3, Cagle Fall 2016
Member of USF Tampa, Team 1-3, Cagle Fall 2016
USFT-CAGLE-F16S1G3
5 Members
14 Guides authored
