Difficulty

Moderate

Steps

17

Time Required

                          20 - 45 minutes

Sections

4

  • Battery
  • 2 steps
  • Exterior Case
  • 7 steps
  • Interior Case
  • 5 steps
  • LCD Screen
  • 3 steps

Flags

0

  • BackFujifilm FinePix XP80

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Open the side panel which houses the battery compartment. Press the center button down and twist the dial.

Open the side panel which houses the battery compartment. Press the center button down and twist the dial.

1024

Step 2

  • Release the battery from its secured position by pulling the orange tab back. The battery can then be removed from its compartment.

Release the battery from its secured position by pulling the orange tab back. The battery can then be removed from its compartment.

Step 3

              Exterior Case
  • Using a Phillips PH000 bit, remove the five 2mm screws on the bottom of the camera.

Using a Phillips PH000 bit, remove the five 2mm screws on the bottom of the camera.

Step 4

  • Using a H1.3 hex head bit, remove the two 2mm screws from the top of the camera.

Using a H1.3 hex head bit, remove the two 2mm screws from the top of the camera.

Step 5

  • Using a H1.3 hex head bit, remove the two 2mm screws on the side of the camera.

Using a H1.3 hex head bit, remove the two 2mm screws on the side of the camera.

Step 6

  • Using a plastic opening tool, gently pry up the edge of the button case, located at the top of the camera, until it unclips.

Using a plastic opening tool, gently pry up the edge of the button case, located at the top of the camera, until it unclips.

Step 7

  • Gently pry the side area of the case apart.

Gently pry the side area of the case apart.

Step 8

  • Continue using the opening tool on the bottom of the camera to gently pry the case apart.

Continue using the opening tool on the bottom of the camera to gently pry the case apart.

Step 9

  • Use the plastic opening tool to carefully pry the yellow front panel completely away from the camera.
  • Use your hands to take off the yellow back panel.

Use the plastic opening tool to carefully pry the yellow front panel completely away from the camera.

Use your hands to take off the yellow back panel.

Step 10

              Interior Case
  • Using the H1.3 hex head bit, remove the four screws on the front of the camera.

Using the H1.3 hex head bit, remove the four screws on the front of the camera.

Step 11

  • Using the H1.3 hex head bit, remove the screw on the back of the camera.

Using the H1.3 hex head bit, remove the screw on the back of the camera.

Step 12

  • Open the battery compartment on the side of the camera.
  • Using your plastic opening tool, carefully pry the two clips apart as indicated in the photo.

Open the battery compartment on the side of the camera.

Using your plastic opening tool, carefully pry the two clips apart as indicated in the photo.

Step 13

  • Unclip the front interior panel from the top, bottom and side of the camera.

Unclip the front interior panel from the top, bottom and side of the camera.

Step 14

  • Gently open the camera, noting the presence of two orange tapes along one side that connect the motherboard to the LCD screen.
  • Open the camera like a book and lay both sides flat next to one another, leaving the orange tapes connected.

Gently open the camera, noting the presence of two orange tapes along one side that connect the motherboard to the LCD screen.

Open the camera like a book and lay both sides flat next to one another, leaving the orange tapes connected.

Step 15

              LCD Screen
  • Once you expose the inside of the camera, use the PH000 Phillips head bit and remove the four screws as shown.
  • Carefully remove the tape binding the screen to the camera.

Once you expose the inside of the camera, use the PH000 Phillips head bit and remove the four screws as shown.

Carefully remove the tape binding the screen to the camera.

Step 16

  • Gently pry the LCD screen from the case, using a plastic opening tool.

Gently pry the LCD screen from the case, using a plastic opening tool.

Step 17

  • Unclip the LCD data line from the mother board, using the plastic opening tool.

Unclip the LCD data line from the mother board, using the plastic opening tool.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Daniela Pesci

Member since: 09/28/2016

194 Reputation

                                      2 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team 1-3, Cagle Fall 2016                        

                                                  Member of USF Tampa, Team 1-3, Cagle Fall 2016 



                    USFT-CAGLE-F16S1G3                     


                                            5 Members                     


                                            14 Guides authored