Fujifilm Finepix Xp50 Lcd Screen Replacement Repair Guide

Difficulty

Moderate

Steps

10

Time Required

                          10 - 20 minutes            

Sections

2

• Rear Case
• 6 steps
• LCD Screen
• 4 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

• BackFujifilm FinePix XP50

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

What you need

Step 1

              Rear Case               

• Using 1.5mm Hex Screwdriver, remove two 3.0 mm hex screws on the front of the camera.
• Using Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.

Using 1.5mm Hex Screwdriver, remove two 3.0 mm hex screws on the front of the camera.

Using Phillips #00 screwdriver, remove two 3.0 mm screws on the bottom of the front face.

1024

Step 2

• Using Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back.
• Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Using Phillips #00 screwdriver, remove 3.0 mm screws on the bottom of the camera closer to the back.

Using Phillips #00 screwdriver remove two 3.0 mm screws on the back of the camera. This will remove the eyelet for the camera strap and the rear cover.

Step 3

• Using Phillips #00 screwdriver, remove the two 3.0 mm screws.

Using Phillips #00 screwdriver, remove the two 3.0 mm screws.

Step 4

• Using 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel.
• Using Phillips #00 screwdriver, remove 3.0 mm screw on bottom edge.
• Once both screws are removed the silver side casing will slide off.

Using 1.5mm Hex screwdriver, remove 3.0 mm hex screw on top edge of silver panel.

Using Phillips #00 screwdriver, remove 3.0 mm screw on bottom edge.

Once both screws are removed the silver side casing will slide off.

Step 5

• Unlatch the four clasps located on each side of the camera by hand.
• The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm FinePix XP50 Battery Replacement for instructions.

Unlatch the four clasps located on each side of the camera by hand.

The fourth clasp is concealed by the battery door. To reach the clasp see Fujifilm FinePix XP50 Battery Replacement for instructions.

Step 6

• Using Phillips #00 screwdriver, remove seven 3.0 mm screws.
• Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.
• The rear panel is now free from the camera.

Using Phillips #00 screwdriver, remove seven 3.0 mm screws.

Remove the remaining five 3.0 mm screws which hold the rear case and the control panel together.

The rear panel is now free from the camera.

Step 7

              LCD Screen               

• Take the spudger and wedge it in between the screen and the frame.
• Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.

Take the spudger and wedge it in between the screen and the frame.

Slowly make your way around the screen with the spudger just enough to separate the screen from the frame.

Step 8

• Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame.
• Make your way around with the spudger just enough to separate the screen and frame once again.

Take the spudger again and wedge it in the thinner frame to pry the LCD screen from the frame.

Make your way around with the spudger just enough to separate the screen and frame once again.

Step 9

• Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame.
• Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.

Take the spudger and wedge it very carefully between the LCD screen and the very thin and fragile frame.

Very carefully make your way around the frame with the spudger, while making sure not to use too much force. Otherwise the screen will be damaged.

Step 10

• Detach the LCD screen from the motherboard by detaching the orange ribbon.

Detach the LCD screen from the motherboard by detaching the orange ribbon.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 

                    Catherine Daniel                     

Member since: 03/20/2015

396 Reputation

                                      3 Guides authored                  



                       Badges:
                       11







                                                        +8 more badges                           

Team

                       Baylor, Team 2-4, Grigsby Spring 2015                        

                                                  Member of Baylor, Team 2-4, Grigsby Spring 2015 



                    BU-GRIGSBY-S15S2G4                     


                                            4 Members                     


                                            8 Guides authored