Fujifilm Finepix Xp10Se Rear Control Panel Replacement Repair Guide

Difficulty

Difficult

Steps

12

Time Required

                          40 minutes            

Sections

4

• Front Cover
• 4 steps
• Lens
• 3 steps
• LCD
• 3 steps
• Rear Control Panel
• 2 steps

Flags

3

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

Inconsistent Images

Updating the images on this guide to be more consistent with the prerequisites would increase its awesomeness.

Better Introduction

Improve this guide by completing or revising its introduction.

• BackFujifilm FinePix XP10SE

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

What you need

Step 1

              Front Cover               

• Use a screwdriver to remove the four screws from the top and bottom of the camera. Remove the screws securing the lanyard as well.
• Use a T5 Torx bit to secure the exterior decorative cover of the device.

Use a screwdriver to remove the four screws from the top and bottom of the camera. Remove the screws securing the lanyard as well.

Use a T5 Torx bit to secure the exterior decorative cover of the device.

1024

Step 2

• Use a plastic opening tool to detach the case.

Use a plastic opening tool to detach the case.

Step 3

• Use the plastic opening tool to cautiously pry the casing off of the camera.

Use the plastic opening tool to cautiously pry the casing off of the camera.

Step 4

• Carefully slide the case to the left. Avoid cracking the case on the lens.

Carefully slide the case to the left. Avoid cracking the case on the lens.

Step 5

              Lens               

• Remove the screws from the lens cover

Remove the screws from the lens cover

Step 6

• Remove the screws from the side metal cover of outer case.

Remove the screws from the side metal cover of outer case.

Step 7

• Gently remove the Lens from the housing.

Gently remove the Lens from the housing.

Step 8

              LCD               

• Locate the securing tabs of the housing unit.
• Using the spongerslowly work your way around the outside of the case using the sponging tool to pry open the case.
• *** Take extreme caution when doing this being careful not to break the securing tabs of the housing.

Locate the securing tabs of the housing unit.

Using the spongerslowly work your way around the outside of the case using the sponging tool to pry open the case.

*** Take extreme caution when doing this being careful not to break the securing tabs of the housing.

Step 9

• Once the case is open locate the Ribbon cable attachment for the LCD screen.
• Carefully ensure that the LCD screen is free from all attachments and any tape securing the ribbon cable is released.

Once the case is open locate the Ribbon cable attachment for the LCD screen.

Carefully ensure that the LCD screen is free from all attachments and any tape securing the ribbon cable is released.

Step 10

• Gently lift up on the black securing bar of the ribbon cable in order to free it from the units motherboard, thus releasing the LCD from the computer.

Gently lift up on the black securing bar of the ribbon cable in order to free it from the units motherboard, thus releasing the LCD from the computer.

Step 11

              Rear Control Panel               

• Locate the ribbon cable attachment for the rear panel controls.
• Gently lift the ribbon cable securing bar and slide the ribbon cable from the socket in order to remove the rear control panel.

Locate the ribbon cable attachment for the rear panel controls.

Gently lift the ribbon cable securing bar and slide the ribbon cable from the socket in order to remove the rear control panel.

Step 12

• Locate the six screws on the control panel.
• **two of the screws may be covered by tape. Remove the tape to access them.
• Use the PH000 Phillip’s screwdriver bit from the Ifixit driver kit to remove the screws and free the control panel from the unit.

Locate the six screws on the control panel.

**two of the screws may be covered by tape. Remove the tape to access them.

Use the PH000 Phillip’s screwdriver bit from the Ifixit driver kit to remove the screws and free the control panel from the unit.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             

Author

                                      with 2 other contributors 

                    Bryan                     

Member since: 01/25/2015

598 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges                           

Team

                       Pasco Hernando, Team 5-1, Prince Winter 2015                        

                                                  Member of Pasco Hernando, Team 5-1, Prince Winter 2015 



                    PHSC-PRINCE-W15S5G1                     


                                            5 Members                     


                                            10 Guides authored