Difficulty

Moderate

Steps

10

Time Required

                          20 - 25 minutes

Sections

2

  • LCD Screen
  • 4 steps
  • Lens
  • 6 steps

Flags

1

Missed a Step

Oops! This guide is currently missing some important steps.

  • BackFujifilm FinePix T500

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              LCD Screen
  • Unscrew the six 3.5mm Philips head from the outer casing.

Unscrew the six 3.5mm Philips head from the outer casing.

1024

Step 2

  • Open the battery chamber and remove the battery.
  • Pry the front half of the casing from the camera.
  • Be careful that the sensor cover—the small piece of translucent plastic—doesn’t fall out of place. Return it to its original location if it does.

Open the battery chamber and remove the battery.

Pry the front half of the casing from the camera.

Be careful that the sensor cover—the small piece of translucent plastic—doesn’t fall out of place. Return it to its original location if it does.

Step 3

  • Pry the back half of the casing from the camera.
  • Be careful when maneuvering the camera without the casing on as the LCD screen is not fastened to anything.

Pry the back half of the casing from the camera.

Be careful when maneuvering the camera without the casing on as the LCD screen is not fastened to anything.

Step 4

  • Lift the LCD screen out of the camera.
  • There is a tab that keeps in place the ribbon that attaches the screen and motherboard. Lift this up using the spudger and disconnect the screen from the motherboard.

Lift the LCD screen out of the camera.

There is a tab that keeps in place the ribbon that attaches the screen and motherboard. Lift this up using the spudger and disconnect the screen from the motherboard.

Step 5

              Lens
  • Unscrew the 3.5 mm Phillips head screw from the corner of the camera.

Unscrew the 3.5 mm Phillips head screw from the corner of the camera.

Step 6

  • Pry the center casing off the camera. This is best done by separating the top and side sections individually.

Pry the center casing off the camera. This is best done by separating the top and side sections individually.

Step 7

  • Unscrew the two 3.5 mm Phillips head screws in the metal plate.

Unscrew the two 3.5 mm Phillips head screws in the metal plate.

Step 8

  • Pry the metal plate out using the spudger.

Pry the metal plate out using the spudger.

Step 9

  • Peel back the strip of black tape to reveal a red and black wire.
  • Detach the orange ribbon by gently pulling on it.
  • Detach the golden ribbon by gently lifting it with the spudger.

Peel back the strip of black tape to reveal a red and black wire.

Detach the orange ribbon by gently pulling on it.

Detach the golden ribbon by gently lifting it with the spudger.

Step 10

  • The lens should now be free to simply be pushed out of its socket.
  • The black and red wires that were exposed previously may be in the way of removing the lens and may break. If they do, you will need to solder these wires back into place upon reassembly.

The lens should now be free to simply be pushed out of its socket.

The black and red wires that were exposed previously may be in the way of removing the lens and may break. If they do, you will need to solder these wires back into place upon reassembly.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Brian Lasher

Member since: 01/16/2015

313 Reputation

                                      3 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       USF Tampa, Team 19-3, Blackwell Winter 2015                        

                                                  Member of USF Tampa, Team 19-3, Blackwell Winter 2015 



                    USFT-BLACKWELL-W15S19G3                     


                                            4 Members                     


                                            10 Guides authored