Difficulty
Moderate
Steps
9
Time Required
45 minutes
Sections
2
- Battery Door
- 7 steps
- Flash Lid Spring
- 2 steps
Flags
1
Better Introduction
Improve this guide by completing or revising its introduction.
BackFujifilm FinePix S8630
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
Battery Door
- Remove the M3 x 4mm screws from the bottom of your device as indicated by the picture. using the Philips Head J0 Screw Driver Bit .
Remove the M3 x 4mm screws from the bottom of your device as indicated by the picture. using the Philips Head J0 Screw Driver Bit .
1024
Step 2
- Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the left side of the device as indicated by the pictures.
Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the left side of the device as indicated by the pictures.
Step 3
- Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the right side of the device as indicated by the pictures.
Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the right side of the device as indicated by the pictures.
Step 4
- Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the camera flash lid as indicated by the picture.
- Remove the plastic cover from the flash lid by gentle pulling them apart or using the plastic opening tool.
Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the camera flash lid as indicated by the picture.
Remove the plastic cover from the flash lid by gentle pulling them apart or using the plastic opening tool.
Step 5
- Fold the lid down in order to access and remove the final M3 x 4mm screw using your Philips Head Screwdriver.
Fold the lid down in order to access and remove the final M3 x 4mm screw using your Philips Head Screwdriver.
Step 6
- Use the plastic opening tool to pry the back and front casings of the camera apart.
- Once pried apart use your hands to pull off the back plate of the camera.
- You will need to apply a little bit of force to remove the back plate.
Use the plastic opening tool to pry the back and front casings of the camera apart.
Once pried apart use your hands to pull off the back plate of the camera.
You will need to apply a little bit of force to remove the back plate.
Step 7
- Once the back plate is removed twist the battery cover clockwise and it should easily dislodge.
Once the back plate is removed twist the battery cover clockwise and it should easily dislodge.
Step 8
Flash Lid Spring
- Firmly grasp the flash bulb lid and remove the lid from the camera.
Firmly grasp the flash bulb lid and remove the lid from the camera.
Step 9
- Locate the spring and grasp with the tweezers.
- Pinch and compress the spring to remove it from the camera housing.
- Slide the lever that was holding the spring out of the camera housing.
Locate the spring and grasp with the tweezers.
Pinch and compress the spring to remove it from the camera housing.
Slide the lever that was holding the spring out of the camera housing.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 5 other contributors
Colton Lancsarics
Member since: 02/10/2016
731 Reputation
6 Guides authored
Badges:
13
+10 more badges
Team
USF Tampa, Team 3-2, Sullivan Spring 2016
Member of USF Tampa, Team 3-2, Sullivan Spring 2016
USFT-SULLIVAN-S16S3G2
4 Members
12 Guides authored
