Difficulty

Easy

Steps

7

Time Required

                          35 minutes

Sections

1

  • Battery Door
  • 7 steps

Flags

0

  • BackFujifilm FinePix S8630

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery Door
  • Remove the M3 x 4mm screws from the bottom of your device as indicated by the picture. using the Philips Head J0 Screw Driver Bit .

Remove the M3 x 4mm screws from the bottom of your device as indicated by the picture. using the Philips Head J0 Screw Driver Bit .

1024

Step 2

  • Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the left side of the device as indicated by the pictures.

Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the left side of the device as indicated by the pictures.

Step 3

  • Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the right side of the device as indicated by the pictures.

Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the right side of the device as indicated by the pictures.

Step 4

  • Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the camera flash lid as indicated by the picture.
  • Remove the plastic cover from the flash lid by gentle pulling them apart or using the plastic opening tool.

Use your Philips Head Screwdriver to remove the M3 x 4mm screws from the camera flash lid as indicated by the picture.

Remove the plastic cover from the flash lid by gentle pulling them apart or using the plastic opening tool.

Step 5

  • Fold the lid down in order to access and remove the final M3 x 4mm screw using your Philips Head Screwdriver.

Fold the lid down in order to access and remove the final M3 x 4mm screw using your Philips Head Screwdriver.

Step 6

  • Use the plastic opening tool to pry the back and front casings of the camera apart.
  • Once pried apart use your hands to pull off the back plate of the camera.
  • You will need to apply a little bit of force to remove the back plate.

Use the plastic opening tool to pry the back and front casings of the camera apart.

Once pried apart use your hands to pull off the back plate of the camera.

You will need to apply a little bit of force to remove the back plate.

Step 7

  • Once the back plate is removed twist the battery cover clockwise and it should easily dislodge.

Once the back plate is removed twist the battery cover clockwise and it should easily dislodge.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Colton Lancsarics

Member since: 02/10/2016

731 Reputation

                                      6 Guides authored                  



                       Badges:
                       13







                                                        +10 more badges

Team

                       USF Tampa, Team 3-2, Sullivan Spring 2016                        

                                                  Member of USF Tampa, Team 3-2, Sullivan Spring 2016 



                    USFT-SULLIVAN-S16S3G2                     


                                            4 Members                     


                                            12 Guides authored

norman laundry - Dec 13, 2018

Reply

I have just replaced the battery door.

There is no need to to do Step 7.

At step 6 when prying the front and back open.

You can insert the new battery cover simply by inserting the cover on an angle.

The two lugs will just fit into the cavity.

Close and insert all screws.

Job is finished.