Difficulty

Moderate

Steps

13

Time Required

                          15 - 20 minutes

Sections

5

  • Battery
  • 3 steps
  • Back Cover
  • 3 steps
  • LCD Screen
  • 2 steps
  • Battery Compartment
  • 1 step
  • Motherboard
  • 4 steps

Flags

0

  • BackFujiFilm FinePix S5100

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Ensure your camera is in the off position.
  • Orient the camera upside down with the lens facing to the left and the battery compartment facing directly toward you.

Ensure your camera is in the off position.

Orient the camera upside down with the lens facing to the left and the battery compartment facing directly toward you.

1024

Step 2

  • Open the battery door by pushing down and in the direction of the arrow on the door.

Open the battery door by pushing down and in the direction of the arrow on the door.

Step 3

  • Remove four AA batteries from the camera.

Remove four AA batteries from the camera.

Step 4

              Back Cover
  • Turn the camera so the screen is facing you and the camera lens is facing away from you.

Turn the camera so the screen is facing you and the camera lens is facing away from you.

Step 5

  • Remove two 0.9mm Phillips #000 screws from the right side of the camera.
  • Remove one 0.6mm Phillips #000 screw from the left side of the camera.
  • Remove two 0.6mm Phillips #000 screws from the bottom side of the camera.
  • When replacing the back cover on the camera, there will be an audible click which ensures the cover has completely seated with the rest of the camera.

Remove two 0.9mm Phillips #000 screws from the right side of the camera.

Remove one 0.6mm Phillips #000 screw from the left side of the camera.

Remove two 0.6mm Phillips #000 screws from the bottom side of the camera.

When replacing the back cover on the camera, there will be an audible click which ensures the cover has completely seated with the rest of the camera.

Step 6

  • Carefully pull the back cover and separate it from the rest of the camera body.
  • Carefully flip up the top of the tan colored tab to disconnect the ribbon cable and completely remove the back cover.

Carefully pull the back cover and separate it from the rest of the camera body.

Carefully flip up the top of the tan colored tab to disconnect the ribbon cable and completely remove the back cover.

Step 7

              LCD Screen
  • Remove the two 1.3mm Phillips #000 screws from the LCD frame.

Remove the two 1.3mm Phillips #000 screws from the LCD frame.

Step 8

  • Carefully using your hand, grab the LCD screen and pull upward and away from the motherboard.
  • Carefully using your hand, remove the tan digital tape by disconnecting it from the receiving port.
  • Remove the entire LCD screen from the motherboard.

Carefully using your hand, grab the LCD screen and pull upward and away from the motherboard.

Carefully using your hand, remove the tan digital tape by disconnecting it from the receiving port.

Remove the entire LCD screen from the motherboard.

Step 9

              Battery Compartment
  • Remove the single 1.3mm Phillips #000 screw.
  • Carefully remove the battery compartment from the rest of the camera.

Remove the single 1.3mm Phillips #000 screw.

Carefully remove the battery compartment from the rest of the camera.

Step 10

              Motherboard
  • Carefully grab and remove the upper level motherboard from the camera.

Carefully grab and remove the upper level motherboard from the camera.

Step 11

  • Remove three 0.8mm Phillips #000 screws from the motherboard.

Remove three 0.8mm Phillips #000 screws from the motherboard.

Step 12

  • Carefully remove the tan digital tape from the receiving port.

Carefully remove the tan digital tape from the receiving port.

Step 13

  • Carefully remove the lower level motherboard from the camera and set aside.

Carefully remove the lower level motherboard from the camera and set aside.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 


                    Evans

Member since: 09/16/2019

586 Reputation

                                      6 Guides authored                  



                       Badges:
                       10







                                                        +7 more badges

Team

                       Embry-Riddle Aeronautical University, Team S6-G1, Salas Fall 2019                        

                                                  Member of Embry-Riddle Aeronautical University, Team S6-G1, Salas Fall 2019 



                    ERAU-SALAS-F19S6G1                     


                                            4 Members                     


                                            8 Guides authored