Difficulty
Easy
Steps
9
Time Required
35 minutes
Sections
3
- Battery
- 2 steps
- Rear Case
- 6 steps
- Battery Compartment Door
- 1 step
Flags
0
BackFujifilm FinePix S4800
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Battery
- Make sure that the camera is powered off before continuing.
- Rotate the camera so that the label on the base of the camera is facing up.
- On the battery compartment door, there is a slider that says “open”. Slide it down and push the door to the right to release the door.
Make sure that the camera is powered off before continuing.
Rotate the camera so that the label on the base of the camera is facing up.
On the battery compartment door, there is a slider that says “open”. Slide it down and push the door to the right to release the door.
1024
Step 2
- Remove all four batteries and set them aside.
- When replacing the batteries, be sure to note the markings on the face of the battery compartment. These markings let you know which side of the battery ("+" or “-”) needs to be facing up in each slot.
Remove all four batteries and set them aside.
When replacing the batteries, be sure to note the markings on the face of the battery compartment. These markings let you know which side of the battery ("+" or “-”) needs to be facing up in each slot.
Step 3
Rear Case
- Remove the three 5.0 mm JIS #000 screws on the bottom of the camera.
Remove the three 5.0 mm JIS #000 screws on the bottom of the camera.
Step 4
- Rotate the camera so that the HDMI port is facing up.
- Remove the two 5.0 mm JIS #000 screws.
Rotate the camera so that the HDMI port is facing up.
Remove the two 5.0 mm JIS #000 screws.
Step 5
- Rotate the camera so that the text “30x superwide 24-720mm” is facing up.
- Remove the two 5.0 mm JIS #000 screws.
Rotate the camera so that the text “30x superwide 24-720mm” is facing up.
Step 6
- Press the pop-up button highlighted in the picture to release the flash mechanism.
- Remove the two 5.0 mm JIS #000 screws highlighted in the picture.
Press the pop-up button highlighted in the picture to release the flash mechanism.
Remove the two 5.0 mm JIS #000 screws highlighted in the picture.
Step 7
- Use a plastic opening tool to separate the rear case from the camera on each of the sides until the panel is completely separated.
- The plastic case is fragile, so take your time on each side making sure to pry each side evenly as you continue around the camera with the tool.
Use a plastic opening tool to separate the rear case from the camera on each of the sides until the panel is completely separated.
The plastic case is fragile, so take your time on each side making sure to pry each side evenly as you continue around the camera with the tool.
Step 8
- Gently, remove the rear case from the camera and set it aside.
Gently, remove the rear case from the camera and set it aside.
Step 9
Battery Compartment Door
- Once the rear case is removed, gently separate the battery compartment door from its position.
Once the rear case is removed, gently separate the battery compartment door from its position.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
One other person completed this guide.
Author
with 2 other contributors
Lairhe Barreto Paez
Member since: 02/17/2017
285 Reputation
2 Guides authored
Badges:
7
+4 more badges
Team
USF Tampa, Team S19-G4, Hoffman Spring 2017
Member of USF Tampa, Team S19-G4, Hoffman Spring 2017
USFT-HOFFMAN-S17S19G4
4 Members
16 Guides authored
