Fujifilm Finepix S4200 Motherboard Replacement Repair Guide

Difficulty

Very difficult

Steps

Time Required

                          1 hour

Sections

Motherboard
14 steps

Flags

Better Introduction

Improve this guide by completing or revising its introduction.

BackFujifilm FinePix S4200
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

What you need

Step 1

              Motherboard

Turn off the camera by pushing the switch as shown.

Turn off the camera by pushing the switch as shown.

1024

Step 2

Remove all the 4mm screws from the left, right, and bottom of the camera.
A Phillips #000 screwdriver should be used to remove all nine screws.

Remove all the 4mm screws from the left, right, and bottom of the camera.

A Phillips #000 screwdriver should be used to remove all nine screws.

Step 3

Remove casing part pictured by gently pulling up until casing is fully detached.

Remove casing part pictured by gently pulling up until casing is fully detached.

Step 4

Remove the 4 mm screws on the metal plate. Then remove the 4 mm screws on left side of the camera, and remove the two 4mm screws on right side.
Use the Phillips #000 screwdriver to avoid stripping the screws.

Remove the 4 mm screws on the metal plate. Then remove the 4 mm screws on left side of the camera, and remove the two 4mm screws on right side.

Use the Phillips #000 screwdriver to avoid stripping the screws.

Step 5

Remove the top casing by pulling upwards.
To remove orange tab gently pull on the tab until it is detached from the clamping device on the motherboard.

Remove the top casing by pulling upwards.

To remove orange tab gently pull on the tab until it is detached from the clamping device on the motherboard.

Step 6

Carefully remove LCD screen.
Gently pull on orange tab until it is free.
This orange strip is susceptible to tearing.

Carefully remove LCD screen.

Gently pull on orange tab until it is free.

This orange strip is susceptible to tearing.

Step 7

Remove remaining 4mm screw.
Detach metal plate by lifting plate upwards.

Remove remaining 4mm screw.

Detach metal plate by lifting plate upwards.

Step 8

Remove remaining orange tabs on motherboard. Gently pull on each orange tab until it is free. Make sure all tabs are free (check markers on image).

Remove remaining orange tabs on motherboard. Gently pull on each orange tab until it is free. Make sure all tabs are free (check markers on image).

Step 9

Remove the 4mm screws in the corners of the motherboard.

Remove the 4mm screws in the corners of the motherboard.

Step 10

Use a soldering iron to melt the solder and disconnect the five connections shown.
After removing the soldered connections, they must be given ample time to cool before moving to the next step.

Use a soldering iron to melt the solder and disconnect the five connections shown.

After removing the soldered connections, they must be given ample time to cool before moving to the next step.

Step 11

Remove the motherboard. It should be free of all connections at this point and can be lifted with ease.

Remove the motherboard. It should be free of all connections at this point and can be lifted with ease.

Step 12

Replace the old motherboard with a new motherboard.

Replace the old motherboard with a new motherboard.

Step 13

Reconnect the orange strips to their designated connections.
Be gentle when reconnecting the orange strips as they are susceptible to tearing.

Reconnect the orange strips to their designated connections.

Be gentle when reconnecting the orange strips as they are susceptible to tearing.

Step 14

Resolder all the connections and wire onto the new motherboard
After soldering the connections, they must be given ample time to cool before moving to the next step.
After given enough time and all the connections on new motherboard are secured, reassemble the camera.

Resolder all the connections and wire onto the new motherboard

After soldering the connections, they must be given ample time to cool before moving to the next step.

After given enough time and all the connections on new motherboard are secured, reassemble the camera.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors

                    Marisol Montes-Castro

Member since: 10/31/2018

229 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge

Team

                       IUPUI, Team S1-G5, Harley Fall 2018                        

                                                  Member of IUPUI, Team S1-G5, Harley Fall 2018 



                    IUPUI-HARLEY-F18S1G5                     


                                            3 Members                     


                                            4 Guides authored

Better Introduction#

What you need#

Team#

Better Introduction

What you need

Team