Difficulty

Difficult

Steps

11

Time Required

                          1 hour

Sections

3

  • Case
  • 5 steps
  • Motherboard
  • 4 steps
  • Bass Speaker
  • 2 steps

Flags

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Missed a Step

Oops! This guide is currently missing some important steps.

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackFugoo Tough XL

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Case
  • Remove four 3 mm screws using a 3 mm Hex screwdriver.

Remove four 3 mm screws using a 3 mm Hex screwdriver.

1024

Step 2

  • Gently remove the outer casing.
  • It should be relatively easy to pull apart, but in the case that it is not easy, don’t be afraid to apply the necessary force to pull them apart.

Gently remove the outer casing.

It should be relatively easy to pull apart, but in the case that it is not easy, don’t be afraid to apply the necessary force to pull them apart.

Step 3

  • Pull the device from the external case.
  • Remove four 12 mm screws using a T10 Torx screwdriver.
  • Remove eight 6 mm screws using a T10 Torx screwdriver.

Pull the device from the external case.

Remove four 12 mm screws using a T10 Torx screwdriver.

Remove eight 6 mm screws using a T10 Torx screwdriver.

Step 4

  • Use your hands to gently remove the side plates.
  • Use the plastic opening tool to pry off the back plate.
  • It is best to work on the side with the Fugoo trademark.

Use your hands to gently remove the side plates.

Use the plastic opening tool to pry off the back plate.

It is best to work on the side with the Fugoo trademark.

Step 5

  • Slowly pull the front casing from the back casing. If possible, try to avoid putting any tension on the connected cables.
  • Separate the two at a slow, consistent pace to avoid damaging the speaker cables.

Slowly pull the front casing from the back casing. If possible, try to avoid putting any tension on the connected cables.

Separate the two at a slow, consistent pace to avoid damaging the speaker cables.

Step 6

              Motherboard
  • Carefully untangle the wires that connect the speaker to the motherboard.

Carefully untangle the wires that connect the speaker to the motherboard.

Step 7

  • Use tweezers to remove the two ribbon wires on the left and right side of motherboard.
  • Do not pull the cables by the cord, as this could damage the cables and the motherboard. It is best to always disconnect the cables from the base, which is closest to the motherboard, using an iFixit opening tool.

Use tweezers to remove the two ribbon wires on the left and right side of motherboard.

Do not pull the cables by the cord, as this could damage the cables and the motherboard. It is best to always disconnect the cables from the base, which is closest to the motherboard, using an iFixit opening tool.

Step 8

  • Pull the motherboard halfway out.
  • Gently unplug the ribbon using the tweezers.
  • There is a hidden ribbon on the motherboard, that becomes visible once the motherboard has been pulled out.

Pull the motherboard halfway out.

Gently unplug the ribbon using the tweezers.

There is a hidden ribbon on the motherboard, that becomes visible once the motherboard has been pulled out.

Step 9

  • Remove the motherboard and battery.
  • Remove four 3 mm screws from the motherboard using a 3 mm Hex screwdriver.

Remove the motherboard and battery.

Remove four 3 mm screws from the motherboard using a 3 mm Hex screwdriver.

Step 10

              Bass Speaker

Step 11

  • Pull the bass speaker from the internal case.

Pull the bass speaker from the internal case.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Austin Coats

Member since: 02/17/2017

107 Reputation

                                      1 Guide authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       USF Tampa, Team S19-G1, Hoffman Spring 2017                        

                                                  Member of USF Tampa, Team S19-G1, Hoffman Spring 2017 



                    USFT-HOFFMAN-S17S19G1                     


                                            4 Members                     


                                            5 Guides authored

Marcin Kopera - Oct 2, 2017

Reply

Hello, what is the power of this loudspeaker for resistances Ω, and RMS