Fugoo Style Xl Motherboard Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          1 hour

Sections

Fabric Case
2 steps
Motherboard
12 steps

Flags

BackFugoo Style XL
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Fabric Case

Using your hand, unscrew the large screws underneath the speaker.

Using your hand, unscrew the large screws underneath the speaker.

1024

Step 2

Using your hand, gently lift the large plastic tab secured to the rubber holding.
After lifting the tab, slide the speaker out of its case.
Ensure the tab is lifted only slightly above the rubber holding. Bending the plastic tab too far could result in damage to the case.

Using your hand, gently lift the large plastic tab secured to the rubber holding.

After lifting the tab, slide the speaker out of its case.

Ensure the tab is lifted only slightly above the rubber holding. Bending the plastic tab too far could result in damage to the case.

Step 3

              Motherboard

Remove the 8 screws (4 on each side) that hold the covers that conceal the bass speakers. Remove these 3mm screws using a #2.0 Hex screwdriver.

Remove the 8 screws (4 on each side) that hold the covers that conceal the bass speakers. Remove these 3mm screws using a #2.0 Hex screwdriver.

Step 4

Using your hand, pull the covers away from the speaker.

Using your hand, pull the covers away from the speaker.

Step 5

Use a #2.0 Hex screwdriver to unscrew the 8 screws shown in the image.

Use a #2.0 Hex screwdriver to unscrew the 8 screws shown in the image.

Step 6

Gently pull apart the front casing from the back casing.
Speakers on the front casing have wires directly connected to the motherboard. Pulling off the casing with force will result in damage.

Gently pull apart the front casing from the back casing.

Speakers on the front casing have wires directly connected to the motherboard. Pulling off the casing with force will result in damage.

Step 7

Using a pair of tweezers or your hand, carefully remove the red bundled cable connectors from the motherboard.
When the red bundled cable connectors are disconnected, set the outer casing aside.

Using a pair of tweezers or your hand, carefully remove the red bundled cable connectors from the motherboard.

When the red bundled cable connectors are disconnected, set the outer casing aside.

Step 8

Untangle any blue bundled cable connectors and gently remove them from the motherboard using a pair of tweezers.

Untangle any blue bundled cable connectors and gently remove them from the motherboard using a pair of tweezers.

Step 9

Carefully untangle and remove the white bundled cable connectors from the motherboard.

Carefully untangle and remove the white bundled cable connectors from the motherboard.

Step 10

Using a T9 screwdriver, remove the 8 screws (4 on each speaker) surrounding the midwoofers.
Using your hand, carefully remove the midwoofers.

Using a T9 screwdriver, remove the 8 screws (4 on each speaker) surrounding the midwoofers.

Using your hand, carefully remove the midwoofers.

Step 11

Using a pair of tweezers, lift the padded holding that secures the ZIF connector to the motherboard. The connector will release from the motherboard once the padding is lifted.
Do not pull on the cables themselves. Doing so can damage the cables. Always remove the ZIF connector by gently lifting the padding securing them to the motherboard.

Using a pair of tweezers, lift the padded holding that secures the ZIF connector to the motherboard. The connector will release from the motherboard once the padding is lifted.

Do not pull on the cables themselves. Doing so can damage the cables. Always remove the ZIF connector by gently lifting the padding securing them to the motherboard.

Step 12

Carefully lift the battery and motherboard unit halfway out of the casing. The motherboard is connected to the battery directly.
There is a small coaxial cable connected underneath the motherboard. Using a pair of tweezers, carefully disconnect and remove the cable from under the adhesive tape.
When the cable is disconnected, fully remove the motherboard and battery unit.

Carefully lift the battery and motherboard unit halfway out of the casing. The motherboard is connected to the battery directly.

There is a small coaxial cable connected underneath the motherboard. Using a pair of tweezers, carefully disconnect and remove the cable from under the adhesive tape.

When the cable is disconnected, fully remove the motherboard and battery unit.

Step 13

Remove the 3mm screws using a #2.0 Hex screwdriver. There are 4 of these screws (2 on each side) that connect the motherboard to the battery unit.
When the screws are removed, use an iFixit opening tool to remove the motherboard from the two clamps securing it to the battery pack.
Beware! The motherboard is not fully disconnected from the battery even when removed from the clamps.

Remove the 3mm screws using a #2.0 Hex screwdriver. There are 4 of these screws (2 on each side) that connect the motherboard to the battery unit.

When the screws are removed, use an iFixit opening tool to remove the motherboard from the two clamps securing it to the battery pack.

Beware! The motherboard is not fully disconnected from the battery even when removed from the clamps.

Step 14

Using tweezers or your hand, carefully disconnect the bundled cables connecting the battery to the motherboard.

Using tweezers or your hand, carefully disconnect the bundled cables connecting the battery to the motherboard.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 4 other contributors

                    James Gifford

Member since: 09/25/2017

573 Reputation

                                      5 Guides authored                  



                       Badges:
                       9







                                                        +6 more badges

Team

                       USF Tampa, Team S3-G4, Cannon Fall 2017                        

                                                  Member of USF Tampa, Team S3-G4, Cannon Fall 2017 



                    USFT-CANNON-F17S3G4                     


                                            4 Members                     


                                            5 Guides authored

Vincent walcott - May 9, 2018

Where can I purchase a replacement mother board?

Rhett Mccrady - May 14, 2021

Are you allowed to tell us where you found a motherboard? I can not find one anywhere for my fugoo

David Langat - Sep 25, 2021

A repair guy lost my charging board, is there a way I can bypass it? Or Where can I get a replacement?

Introduction#

What you need#

Team#

Introduction

What you need

Team