Frosty Factory Model 113 Rubber Gasket Seal Replacement Repair Guide

Difficulty

Easy

Steps

Time Required

                          5 minutes

Sections

Rubber Gasket Seal
7 steps

Flags

BackKitchen Appliance
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Here is a link to an online pdf of the device’s manual.

Step 1

              Rubber Gasket Seal

We will be replacing the rubber gasket seal for this margarita machine.
The seal is the black ring seen in the photo.

We will be replacing the rubber gasket seal for this margarita machine.

The seal is the black ring seen in the photo.

1024

Step 2

Unscrew the white knobs that are on the four corners of the faceplate in diagonal pairs.
This will safely release the seal’s pressure.
Place the knobs aside.
Pull the faceplate off the machine.

Unscrew the white knobs that are on the four corners of the faceplate in diagonal pairs.

This will safely release the seal’s pressure.

Place the knobs aside.

Pull the faceplate off the machine.

Step 3

Remove the old seal from the faceplate.
It might be difficult to pull out if you have short nails.

Remove the old seal from the faceplate.

It might be difficult to pull out if you have short nails.

Step 4

Pull out the beater bar. This will make the reassembly easier.
Notice the beater shaft on the beater bar that attaches to the white faceplate bushing on the faceplate that the seal was on.

Pull out the beater bar. This will make the reassembly easier.

Notice the beater shaft on the beater bar that attaches to the white faceplate bushing on the faceplate that the seal was on.

Step 5

Place the new rubber seal in the frame.
It should slide in easily.
Here is the white faceplate bushing for front end of the beater bar to go into.

Place the new rubber seal in the frame.

It should slide in easily.

Here is the white faceplate bushing for front end of the beater bar to go into.

Step 6

Slide the black carbon ring wrapped end of the beater shaft towards the slot in the machine’s mixing chamber.
Carefully press the beater bar into the machine as far as you can once the black carbon ring end is in the slot.
Gently turn the beater bar clock-wise until the beater shaft catches the driver plate, which will allow you to push the bar closer to the back of the chamber’s wall.

Slide the black carbon ring wrapped end of the beater shaft towards the slot in the machine’s mixing chamber.

Carefully press the beater bar into the machine as far as you can once the black carbon ring end is in the slot.

Gently turn the beater bar clock-wise until the beater shaft catches the driver plate, which will allow you to push the bar closer to the back of the chamber’s wall.

Step 7

Line the faceplate bushing up with beater shaft.
Align the faceplate’s four outer holes along the four screws and push it against the machine.
Screw the knobs back on, once again in diagonal pairs.
If the beater bar does not let the face plate be pressed against the machine enough so that all four knobs can be reattached, then remove the face plate and re-adjust the beater bar to catch the driver plate.

Line the faceplate bushing up with beater shaft.

Align the faceplate’s four outer holes along the four screws and push it against the machine.

Screw the knobs back on, once again in diagonal pairs.

If the beater bar does not let the face plate be pressed against the machine enough so that all four knobs can be reattached, then remove the face plate and re-adjust the beater bar to catch the driver plate.

You will have successfully disassembled, replaced, and then reassembled part of the machine.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Griffin Cadigan

Member since: 10/05/2022

145 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       University of North Texas, Team 1-4, Friess Fall 2022                        

                                                  Member of University of North Texas, Team 1-4, Friess Fall 2022 



                    UNT-FRIESS-F22S1G4                     


                                            1 Member                     


                                            1 Guide authored

Introduction#

Team#

Introduction

Team