Difficulty
Difficult
Steps
4
Time Required
10 minutes
Sections
1
- Camera Stand Battery
- 4 steps
Flags
2
Bullets!
Better coordination with markups and the color/type of bullets will help make this guide more clear!
Incorrect Tools
Help make this guide better by using the correct tools in images and/or text.
BackFLIR FX
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Camera Stand Battery
- Use a plastic opening tool to pry off the plastic bottom cover.
Use a plastic opening tool to pry off the plastic bottom cover.
1024
Step 2
- Unscrew the four screws on the bottom of the stand with a J00 screwdriver.
- Use a plastic opening tool to pry open the bottom of the stand.
- If having a hard time separating the two pieces use the iOpener tool to soften the adhesive under the panel.
- Heat up for 30 seconds. Once it is hot place around the stand to loosen the glue.
Unscrew the four screws on the bottom of the stand with a J00 screwdriver.
Use a plastic opening tool to pry open the bottom of the stand.
If having a hard time separating the two pieces use the iOpener tool to soften the adhesive under the panel.
Heat up for 30 seconds. Once it is hot place around the stand to loosen the glue.
Step 3
- Once you have separated the two parts, use a J00 screwdriver to unscrew the four 1.2 mm screws which connect the metal piece to the top of the the stand.
Once you have separated the two parts, use a J00 screwdriver to unscrew the four 1.2 mm screws which connect the metal piece to the top of the the stand.
Step 4
- When the metal piece is removed, unscrew the four 1.2 mm Phillips #1 screws on the plastic piece of the stand
- Now separate the top of the stand from the plastic bottom piece.
- Unplug the battery from the stand.
When the metal piece is removed, unscrew the four 1.2 mm Phillips #1 screws on the plastic piece of the stand
Now separate the top of the stand from the plastic bottom piece.
Unplug the battery from the stand.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Emily Bell
Member since: 03/20/2017
392 Reputation
3 Guides authored
Badges:
7
+4 more badges
Team
Texas Tech, Team S13-G2, Bennett Spring 2017
Member of Texas Tech, Team S13-G2, Bennett Spring 2017
TTU-BENNETT-S17S13G2
3 Members
6 Guides authored
Mark Krank - Mar 28, 2019
Reply
A couple of suggestions which are;
You do not and should not pry off the bottom (the piece with decal with the QR code and the product info such as the model #). Just use a quarter in the slot and turn counter clockwise and the bottom cover will fall of.
After removing the bottom cover and removing the 4 screws, prying off the bottom base (the part below the silver ring about 0.5” above the bottom of the base) should NOT be done by prying from the hole in the bottom center. Doing it this way will just damage the plastic base and is difficult. The way to remove the bottom part of the base is to use a utility knife (razor blade inside the handle), drag it through the seam immediately below the silver trim piece all of the way around a couple of times twisting the utility knife a little to pry off and then use a flat screw drive to finish prying the bottom base piece off of the main unit. Doing it this way takes about 30 seconds, does not damage the base and permits you to reassemble when finished.
Suggestions continued - opening up the battery compartment.
- The battery is attached to the inside of the case with double sided tape. Just pry the battery gently using a plastic tool (metal tool could damage) working your way around the battery rather than just trying to pry the battery off with 1 large prying motion from 1 place on the battery.
