Difficulty

Moderate

Steps

12

Time Required

Suggest a time??

Sections

3

  • Outer Shell
  • 5 steps
  • Circuit Board
  • 4 steps
  • LCD Screen
  • 3 steps

Flags

0

  • BackFlip Video

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Outer Shell
  • Turn off the device and take the batteries out.
  • Remove metal sticker under the LCD screen with a spudger.
  • This may require a large force to pry off the glued sticker.

Turn off the device and take the batteries out.

Remove metal sticker under the LCD screen with a spudger.

This may require a large force to pry off the glued sticker.

1024

Step 2

  • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

Step 3

  • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

Step 4

  • Open battery door. This can be done by gently depressing and sliding the battery down downward.

Open battery door. This can be done by gently depressing and sliding the battery down downward.

Step 5

  • Use the spudger to separate outer shells.
  • The spudger must be inserted between the shell halves to pry the edges apart.
  • Slowly work around the outside to separate the halves.

Use the spudger to separate outer shells.

The spudger must be inserted between the shell halves to pry the edges apart.

Slowly work around the outside to separate the halves.

Step 6

              Circuit Board
  • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

Step 7

  • Slowly lift the left side of the circuit board.
  • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

Slowly lift the left side of the circuit board.

Do not attempt to remove the circuit board completely yet. It is still connected to the device.

Step 8

  • Disconnect the USB port cable from the back side of the circuit board.

Disconnect the USB port cable from the back side of the circuit board.

Step 9

  • Slide out the battery contacts.
  • Battery contacts
  • Slot where battery contacts were located

Slide out the battery contacts.

Battery contacts

Slot where battery contacts were located

Step 10

              LCD Screen
  • With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

Step 11

  • Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

Step 12

  • Gently pull out ribbon cable.
  • If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.
  • The LCD screen is now removed and can be replaced.

Gently pull out ribbon cable.

If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.

The LCD screen is now removed and can be replaced.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors 


                    Elizabeth

Member since: 04/15/2010

100 Reputation

                                      6 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 26-21, Regan Spring 2010                        

                                                  Member of Cal Poly, Team 26-21, Regan Spring 2010 



                    CPSU-REGAN-S10S26G21                     


                                            4 Members                     


                                            12 Guides authored