Fixing A Misaligned Single Swing Chain Link Gate Repair Guide

Difficulty

Easy

Steps

Time Required

                          15 - 20 minutes

Sections

Fixing a Misaligned Single Swing Chain-link Gate
7 steps

Flags

BackSingle Swing Chain-link Fence
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Thankfully, one of the most common causes of misalignment is the gradual shift of your gate hinges. This can be fixed quickly and with just an open end wrench or a pair of pliers, a marker, and a small carpenter’s level.

What you need

Step 1

              Fixing a Misaligned Single Swing Chain-link Gate

Use your open end wrench or pliers to loosen and remove the nuts on the bottom tension band.
It’s important to begin with the bottom band, as removing the top band first will put pressure on the bottom band and make it harder to unscrew.
Loosen and remove top tension band.
Remove and place gate to the side.

Use your open end wrench or pliers to loosen and remove the nuts on the bottom tension band.

It’s important to begin with the bottom band, as removing the top band first will put pressure on the bottom band and make it harder to unscrew.

Loosen and remove top tension band.

Remove and place gate to the side.

1024

Step 2

Mark the height of hinges on the post.
When loosened, these will fall. If not returned to the hinge’s original distance from each other on the post it may be impossible to reconstruct your gate.
If the hinges have already sagged on your gate before you disassembled, they may need to be raised from their original position to make your gate effective once again.

Mark the height of hinges on the post.

When loosened, these will fall. If not returned to the hinge’s original distance from each other on the post it may be impossible to reconstruct your gate.

If the hinges have already sagged on your gate before you disassembled, they may need to be raised from their original position to make your gate effective once again.

Step 3

Loosen nuts on hinge.
There is no need to remove the nuts and bolts from the hinges, they should now move freely.

Loosen nuts on hinge.

There is no need to remove the nuts and bolts from the hinges, they should now move freely.

Step 4

Realign hinges so that they are perpendicular to the gate when latched.
A gate that was improperly installed may require the hinges to be aligned differently in order for the gate to latch.

Realign hinges so that they are perpendicular to the gate when latched.

A gate that was improperly installed may require the hinges to be aligned differently in order for the gate to latch.

Step 5

Retighten nuts.
Make sure to support the hinges so they remain at the proper height and alignment.

Retighten nuts.

Make sure to support the hinges so they remain at the proper height and alignment.

Step 6

Place the gate back onto its hinges.
Put bolts back into the tension bands, retighten with nuts.

Place the gate back onto its hinges.

Put bolts back into the tension bands, retighten with nuts.

Step 7

Remove any ornament on top of the gate by unscrewing and removing nuts, if necessary.
Place your carpenter’s level flat on top of the gate.
If the bubble is not in the center of the level, your gate is sagging. This is likely because you need to adjust the distance between your hinges in Step 4.
Place the ornament back on, and fasten the bolts.

Remove any ornament on top of the gate by unscrewing and removing nuts, if necessary.

Place your carpenter’s level flat on top of the gate.

If the bubble is not in the center of the level, your gate is sagging. This is likely because you need to adjust the distance between your hinges in Step 4.

Place the ornament back on, and fasten the bolts.

If your gate is still not latching properly or is sagging, you may need to disassemble your gate again and adjust the alignment or height of your hinges until the gate latches properly.

If the problem persists, it’s possible that your post wasn’t installed correctly, your fence may be experiencing pressure from structures leaning on it, or your nuts and bolts may be worn and deficient. These problems will require additional procedures.

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 1 other contributor

                    Levi Smith

Member since: 03/07/2019

172 Reputation

                                      1 Guide authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Missouri Western, Team S1-G4, Cools Stephens Spring 2019                        

                                                  Member of Missouri Western, Team S1-G4, Cools Stephens Spring 2019 



                    MWSU-COOLS STEPHENS-S19S1G4                     


                                            1 Member                     


                                            1 Guide authored

DogLovr Snowflake - May 20, 2021

Thanks! Great detailed instructions and photos.

Rob Harris - Aug 5, 2022

I read your guide and realized why our NEW fence from Lowes is a disaster!No bar on the bottom of the fence,so anyone can slide under it,LIKE MY DOGS DID LOWES!!!Thanks to your article I can now repair it right MYSELF.

Introduction#

What you need#

Team#

Introduction

What you need

Team