Difficulty
Moderate
Steps
4
Time Required
55 minutes
Sections
1
- The Lid when it does not open
- 4 steps
Flags
2
In Progress
This guide is a work in progress. Reload periodically to see the latest changes!
Member-Contributed Guide
An awesome member of our community made this guide. It is not managed by iFixit staff.
BackGraef WK 402
Full Screen
Options
History
Save to Favorites
Download PDF
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
What you need
Step 1
The Lid when it does not open
- The spring loaded mechanism that opened the lid no longer worked. To fix this the metal lid must be disassembled. To accomplish this use a flat head screw driver or a narrow piece of plastic to get in between the sealing ring and the lever
- There are six noses that need to be undone. The marked part will come loose and will lay loosely in the lid. Then the lever can be inserted in two directions but only one is correct. One will notice this immediately because the sled moves much easier.
- Attention: I’m not sure if the photo was taken with the sled in the right direction.
The spring loaded mechanism that opened the lid no longer worked. To fix this the metal lid must be disassembled. To accomplish this use a flat head screw driver or a narrow piece of plastic to get in between the sealing ring and the lever
There are six noses that need to be undone. The marked part will come loose and will lay loosely in the lid. Then the lever can be inserted in two directions but only one is correct. One will notice this immediately because the sled moves much easier.
Attention: I’m not sure if the photo was taken with the sled in the right direction.
1024
Step 2
- To repair the lid the following instructions are not necessary.
- To unscrew the bottom you need a 2.3 mm triangular bit and a Phillips driver.
To repair the lid the following instructions are not necessary.
To unscrew the bottom you need a 2.3 mm triangular bit and a Phillips driver.
Step 3
- To take off the handle. Take a narrow object a flat head screw driver or a spudger and work up the side of the handle. There are four snaps that will release as the screwdriver works its way up. After completing this you can turn the handle part upwards and away.
- Then loosen the two screws at the top end and loosen the two screws from the inside.
To take off the handle. Take a narrow object a flat head screw driver or a spudger and work up the side of the handle. There are four snaps that will release as the screwdriver works its way up. After completing this you can turn the handle part upwards and away.
Then loosen the two screws at the top end and loosen the two screws from the inside.
Step 4
- To loosen internal screws it is best to use a long screwdriver and start through the spout.
To loosen internal screws it is best to use a long screwdriver and start through the spout.
To re-assemble your device work through the steps given in reverse order.
Cancel: I did not complete this guide.
3 other people completed this guide.
These translators are helping us fix the world! Want to contribute? Start translating ›
Special thanks to these translators:
100%
Elijah Holder
Annika Faelker
Author
with 1 other contributor
Andreas Reheis
Member since: 03/19/2017
746 Reputation
6 Guides authored
Badges:
12
+9 more badges
Lennard - Sep 15, 2020
Reply
Hab ein ähnliches Modell ( WK900) bei dem die Deckelhalterung gebrochen war. Hier ist ein 3Ddruckbarer Halter, könnte auch für dieses Modell passen (evt. ist die Gummidichtung dünner hier dünner).
https://www.thingiverse.com/thing:457124…
Thais Benjamin N. Christensen - Mar 4, 2022
Reply
Thanks! Just the guidance I needed :-)
