Fitting Ski Bindings To A New Pair Of Boots Repair Guide

Difficulty

Moderate

Steps

Time Required

                          10 - 20 minutes

Sections

Fitting Ski Bindings to a New Pair of Boots
10 steps

Flags

Featured Student Guide

This guide has been the hard work of our awesome students and is found to be exceptionally cool by the iFixit staff.

BackAlpine Ski
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

The ski binding is the device that connects your ski boot to the ski. When a skier gets a new pair of ski boots or buys the sky of someone else, it’s unnecessary to purchase a new pair of skis or pay someone to adjust the bindings. Instead, you can use this guide to learn how to adjust the bindings yourself.

This guide shows you how to adjust the location of the bindings as well as the DIN setting. Your DIN setting is a function of your height, weight, and a few other personalized parameters. It’s crucial to adjust it for your security and ease.Before using this guide, calculate your DIN setting here.

What you need

Step 1

              Fitting Ski Bindings to a New Pair of Boots

Locate the boot size (in millimeters) on the bottom of the boot.
If the boot size is not on the bottom, check the inner or outer sides of the heel.
In our case, the size is 316mm. However, this may not be the case for everyone.

Locate the boot size (in millimeters) on the bottom of the boot.

If the boot size is not on the bottom, check the inner or outer sides of the heel.

In our case, the size is 316mm. However, this may not be the case for everyone.

1024

Step 2

Place your ski on a flat surface with the ski bindings facing up.
Locate the lever on the side of the heel piece of the binding.
Lift and hold the lever in the upright position.

Place your ski on a flat surface with the ski bindings facing up.

Locate the lever on the side of the heel piece of the binding.

Lift and hold the lever in the upright position.

Step 3

With the lever raised, slide the heel piece until the markers point to the correct range of the boot size.
Given the boot size in this guide is 316mm, the correct range for this ski boot is 311mm - 318mm. This may not be the case for everyone.

With the lever raised, slide the heel piece until the markers point to the correct range of the boot size.

Given the boot size in this guide is 316mm, the correct range for this ski boot is 311mm - 318mm. This may not be the case for everyone.

Step 4

Locate the lever on the toe piece of the binding.
Lift and hold the lever in the upright position.

Locate the lever on the toe piece of the binding.

Step 5

With the lever raised, slide the toe piece until the markers point to the correct boot size range.
Given the boot size in this guide is 316mm, the correct range for this ski boot is 315mm - 322mm. This may not be the case for everyone.

With the lever raised, slide the toe piece until the markers point to the correct boot size range.

Given the boot size in this guide is 316mm, the correct range for this ski boot is 315mm - 322mm. This may not be the case for everyone.

Step 6

Insert the toe of the boot into the toe piece of the binding.
Push down on the boot until the boot clips into the binding. If needed, you can lift the lever on the heel piece to facilitate the procedure.

Insert the toe of the boot into the toe piece of the binding.

Push down on the boot until the boot clips into the binding. If needed, you can lift the lever on the heel piece to facilitate the procedure.

Step 7

Insert the screwdriver in the front of the toe piece.
Loosen the screw until the toe bar moves backwards.
You should be able to fit a piece of paper between the bottom of the boot and the toe bar.

Insert the screwdriver in the front of the toe piece.

Loosen the screw until the toe bar moves backwards.

You should be able to fit a piece of paper between the bottom of the boot and the toe bar.

Step 8

Insert a piece of paper between the bottom of the boot and the toe bar.
Tighten the screw at the front of the toe piece until there is resistance when pulling the paper out.
You should be able to pull the paper out without it ripping but not push it back in.
Over-tightening of the toe bar can be dangerous. Practice caution and take your time.

Insert a piece of paper between the bottom of the boot and the toe bar.

Tighten the screw at the front of the toe piece until there is resistance when pulling the paper out.

You should be able to pull the paper out without it ripping but not push it back in.

Over-tightening of the toe bar can be dangerous. Practice caution and take your time.

Step 9

Adjust the DIN setting on the toe piece to your personalized setting by tightening or loosening the screw on the side of the bindings.
Look at the window on the top of the toe piece to see the current DIN setting.
Skiing with a DIN setting that is too high can be dangerous, because the bidding won’t be activated if the ski is subject to high strains. Use caution to not over-tighten the screw. On the contrary, a low value will cause undesired activations of the binding, which can be dangerous, too.

Adjust the DIN setting on the toe piece to your personalized setting by tightening or loosening the screw on the side of the bindings.

Look at the window on the top of the toe piece to see the current DIN setting.

Skiing with a DIN setting that is too high can be dangerous, because the bidding won’t be activated if the ski is subject to high strains. Use caution to not over-tighten the screw. On the contrary, a low value will cause undesired activations of the binding, which can be dangerous, too.

Step 10

Repeat step 9 but on the heel piece.
Adjust the DIN setting on the heel piece by tightening or loosening the screw on the back.
Look at the window on the top of the heel piece to see the current DIN setting.
Skiing with a DIN setting that is too high can be dangerous. Use caution to not over-tighten the screw.

Repeat step 9 but on the heel piece.

Adjust the DIN setting on the heel piece by tightening or loosening the screw on the back.

Look at the window on the top of the heel piece to see the current DIN setting.

Skiing with a DIN setting that is too high can be dangerous. Use caution to not over-tighten the screw.

Repeat this guide on the other ski and you’re ready to go!

Cancel: I did not complete this guide.

                                                                                      One other person completed this guide.

Author

                                      with 5 other contributors

                    Veronica Contreras

Member since: 02/20/2020

193 Reputation

                                      1 Guide authored                  



                       Badges:
                       5







                                                        +2 more badges

Team

                       UC Davis, Team S1-G3, Andersen Winter 2020                        

                                                  Member of UC Davis, Team S1-G3, Andersen Winter 2020 



                    UCD-ANDERSEN-W20S1G3                     


                                            4 Members                     


                                            5 Guides authored

Featured Student Guide#

Introduction#

What you need#

Team#

Featured Student Guide

Introduction

What you need

Team