Featured
Featured Guide
Difficulty
Easy
Steps
9
Time Required
5 - 10 minutes
Sections
3
- Back Cover
- 2 steps
- Battery
- 2 steps
- Display Module
- 5 steps
Flags
1
Featured Guide
This guide has been found to be exceptionally cool by the iFixit staff.
BackFairphone 3 and 3+
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Back Cover
- Power off your phone before beginning disassembly.
- Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom right of the back cover.
- Pry the back cover up to start separating its plastic clips.
Power off your phone before beginning disassembly.
Insert a thumbnail, or a prying tool like a spudger, into the notch at the bottom right of the back cover.
Pry the back cover up to start separating its plastic clips.
1024
Step 2
- Slide around the bottom right corner of the back cover to loosen the lower plastic clips.
- Lift the back cover to release the rest of the plastic clips and remove it.
- To reinstall the back cover press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.
Slide around the bottom right corner of the back cover to loosen the lower plastic clips.
Lift the back cover to release the rest of the plastic clips and remove it.
To reinstall the back cover press it firmly into place until you hear a snap from the plastic clips to form a seamless connection with the rear side of the phone.
Step 3
Battery
- Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.
- Lever the battery up until you can get a good grip.
Use a fingernail or a prying tool at the marked notch to lever the battery out of its recess.
Lever the battery up until you can get a good grip.
Step 4
- Lift the battery out of its recess and remove it.
Lift the battery out of its recess and remove it.
Step 5
Display Assembly
- Whenever a Phillips #00 screw is mentioned you can also unfasten it with a size #0 bit/screwdriver.
- Remove the thirteen Phillips #00 screws (4 mm length).
Whenever a Phillips #00 screw is mentioned you can also unfasten it with a size #0 bit/screwdriver.
Remove the thirteen Phillips #00 screws (4 mm length).
Step 6
- Make sure to insert the opening pick between the midframe and the display module and not into the small gap next to the screen. Otherwise you’re going to pry up the screen instead of the whole display module.
- Insert an opening pick between the midframe and the display module on the right edge of the phone.
- Slide the opening pick down to the bottom right corner to pry open the plastic clamps of the display module.
Make sure to insert the opening pick between the midframe and the display module and not into the small gap next to the screen. Otherwise you’re going to pry up the screen instead of the whole display module.
Insert an opening pick between the midframe and the display module on the right edge of the phone.
Slide the opening pick down to the bottom right corner to pry open the plastic clamps of the display module.
Step 7
- Slide the opening pick around the bottom right corner and use it to disengage the plastic clamps at the bottom of the display module.
Slide the opening pick around the bottom right corner and use it to disengage the plastic clamps at the bottom of the display module.
Step 8
- Slide the opening pick along the left side to pry the display module up.
- The display module should pop out of the midframe during this process. In case it doesn’t, check for remaining clamps you might have missed.
Slide the opening pick along the left side to pry the display module up.
The display module should pop out of the midframe during this process. In case it doesn’t, check for remaining clamps you might have missed.
Step 9
- Remove the display assembly.
- To reinstall the display-module press it into place on all sides until you can hear a snap from the plastic clamps to make sure it sits flush with the frame.
- If you install a new display: The new display module comes with a white plastic cover held by 2 screws over the processor and the connectors. This needs to be taken off.
Remove the display assembly.
To reinstall the display-module press it into place on all sides until you can hear a snap from the plastic clamps to make sure it sits flush with the frame.
If you install a new display: The new display module comes with a white plastic cover held by 2 screws over the processor and the connectors. This needs to be taken off.
To reassemble your device, follow these instructions in reverse order.
Take your e-waste to an R2 or e-Stewards certified recycler.
Cancel: I did not complete this guide.
26 other people completed this guide.
Author
with 3 other contributors
Dominik Schnabelrauch
Member since: 11/23/2016
158,135 Reputation
649 Guides authored
Badges:
40
+37 more badges
Team
iFixit
Member of iFixit
Community
141 Members
15,769 Guides authored
Bert Ober - Dec 26, 2019
Reply
Pick goes in much easier on the left side. Then round the bottom and work it onto the right side.
Martine R - Sep 1, 2020
Reply
bonjour,
Excellent tutoriel, merci!
Mon Fairphone ne se sent plus de joie!
Martine
hélène Petit - Sep 28, 2020
Reply
Bonjour,
Mon écran est noir depuis une chute, mais il n’y a aucun impact.
Marette - Nov 13, 2021
Je suppose que depuis ce temps là vous avez trouvé une solution…
Mais, à toute fin utile dans cette page, le démontage (nettoyage des contacts) remontage a permis de refaire fonctionner l’écran d’un FAIRPHONE3 qui ne répondait plus au toucher !
La déconnexion-reconnexion de la carte mère y est aussi peut-être pour quelque chose…
Jörg Articus - Oct 23, 2020
Reply
Wichtig: beim Lösen der Klammern der Displayeinheit muss dass Plektrum in die Rille zwischen äusserem Rand und dem Rand der Einheit gesteckt werden. Bitte gesondert darauf hinweisen! Ich habe aus Versehen die Einheit zerlegt, ;-(
Das Foto mit Plektrum an der unteren Schmalseite zeigt dies sehr gut.
Danke für die Anleitung!
