Difficulty

Easy

Steps

6

Time Required

                          2 minutes

Sections

2

  • EVGA GeForce GTX 1080 FTW2 DT GAMING with iCX Cooler PCIe Mounting plate Removal
  • 4 steps
  • EVGA GeForce GTX 1080 FTW2 DT GAMING with iCX Cooler Fan Shroud Removal
  • 2 steps

Flags

5

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Grammar Police

Embrace your inner English teacher and help improve this guide’s grammar!

Needs Better Images

Better photos will improve this guide. Help out by taking, editing, or uploading new ones!

  • BackEVGA GeForce GTX 1080 FTW2 DT GAMING with iCX Cooler PCIe Video Card

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Remove Dust Caps
  • If you have any dust caps over the HDMI or Display Port connections, remove them

If you have any dust caps over the HDMI or Display Port connections, remove them

1024

Step 2

              Remove Back Screws
  • Remove the 3 screws using a Phillips #1 Screwdriver (Red)
  • Remove the 2 Standoffs using a 5mm socket

Remove the 3 screws using a Phillips #1 Screwdriver (Red)

Remove the 2 Standoffs using a 5mm socket

Step 3

  • Remove top screw using a Phillips #0 screwdriver (Blue)
  • Remove the bottom screw and nut using a Phillips #0 screwdriver. Will want to use a finger to hold the nut from spinning while releasing the screw.

Remove top screw using a Phillips #0 screwdriver (Blue)

Remove the bottom screw and nut using a Phillips #0 screwdriver. Will want to use a finger to hold the nut from spinning while releasing the screw.

Step 4

              Slide out the plate
  • Gently slide the plate out from between the back cover and the circuit board. It should come out without much force.
  • If it doesn’t want to budge, check that the right screw was removed from the top of the video card.

Gently slide the plate out from between the back cover and the circuit board. It should come out without much force.

If it doesn’t want to budge, check that the right screw was removed from the top of the video card.

Step 5

              Remove 4 Screws
  • Using the 1.5mm Hex, remove the 4 screws (one on each corner) to release the shroud
  • Note: there is 4 screws on each corner plate, the other 3 screws do not need to be removed.

Using the 1.5mm Hex, remove the 4 screws (one on each corner) to release the shroud

Note: there is 4 screws on each corner plate, the other 3 screws do not need to be removed.

Step 6

              Open the shroud
  • The shoud should be able to be lifted free easily, on the wiring harness for the lights.
  • The connector for the harness is on the inside end end, nearest the power connectors.
  • The connector can be disconnected to completely seperate the shroud, or left connected if just needing access to the fans.

The shoud should be able to be lifted free easily, on the wiring harness for the lights.

The connector for the harness is on the inside end end, nearest the power connectors.

The connector can be disconnected to completely seperate the shroud, or left connected if just needing access to the fans.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Wolphin

Member since: 11/11/2019

1,420 Reputation

                                      8 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges