Difficulty
Easy
Steps
8
Time Required
3 minutes
Sections
3
- Dust Cup
- 1 step
- Brush Roll Cover
- 5 steps
- Belt Latch Assembly
- 2 steps
Flags
0
BackEureka SuctionSeal 2.0 Pet
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Dust Cup
- Place the device upright with the brush roller closest to you.
- Pull up on the latch at the top of the dust cup.
- Tilt the top of the dust cup forward and pull towards yourself, removing the container from the device.
Place the device upright with the brush roller closest to you.
Pull up on the latch at the top of the dust cup.
Tilt the top of the dust cup forward and pull towards yourself, removing the container from the device.
1024
Step 2
Brush Roll Cover
- Locate the gray exhaust filter cover at the top of the vacuum’s base.
- Grip the two tabs in the middle of the filter cover and rotate counter-clockwise.
- Lift the cover away from the vacuum.
Locate the gray exhaust filter cover at the top of the vacuum’s base.
Grip the two tabs in the middle of the filter cover and rotate counter-clockwise.
Lift the cover away from the vacuum.
Step 3
- Pull up and unhook the two front tower latches using two fingers. These are located at the base of the tower.
- Pull up and unhook the latch on the back of the tower.
- Firmly lift the vacuum tower up and out of its stand.
- The exhaust filter cover can be replaced once the tower is removed. It will not affect the steps.
Pull up and unhook the two front tower latches using two fingers. These are located at the base of the tower.
Pull up and unhook the latch on the back of the tower.
Firmly lift the vacuum tower up and out of its stand.
The exhaust filter cover can be replaced once the tower is removed. It will not affect the steps.
Step 4
- Remove the four 20mm screws on the top of the vacuum head’s cover using a JIS 1 screwdriver.
Remove the four 20mm screws on the top of the vacuum head’s cover using a JIS 1 screwdriver.
Step 5
- Turn the vacuum head so that the back is facing you.
- Press the handle release pedal.
- Rotate the top of the motor cover down while pressing on the pedal release.
- The motor cover should rotate from an upright position back towards the ground, as it would if the handle were still attached.
Turn the vacuum head so that the back is facing you.
Press the handle release pedal.
Rotate the top of the motor cover down while pressing on the pedal release.
The motor cover should rotate from an upright position back towards the ground, as it would if the handle were still attached.
Step 6
- Locate the two tabs on the back of the cover.
- Pull up on the tabs and lift the cover away from the device.
Locate the two tabs on the back of the cover.
Pull up on the tabs and lift the cover away from the device.
Step 7
Belt Latch Assembly
- Locate the belt latch assembly. It will be on your right when the brush roll is facing you.
- Remove the two 20mm screws using a JIS 1 screwdriver.
Locate the belt latch assembly. It will be on your right when the brush roll is facing you.
Remove the two 20mm screws using a JIS 1 screwdriver.
Step 8
- Lift up on the belt latch assembly and remove it from the vacuum.
Lift up on the belt latch assembly and remove it from the vacuum.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Grayson Clendenon
Member since: 10/02/2017
571 Reputation
5 Guides authored
Badges:
16
+13 more badges
Team
Cal Poly, Team S4-G5, Livingston Fall 2017
Member of Cal Poly, Team S4-G5, Livingston Fall 2017
CPSU-LIVINGSTON-F17S4G5
3 Members
16 Guides authored
