Eureka 169 J 2 In 1 Quick Up Brush Roll Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          20 - 45 minutes

Sections

Brush roll
8 steps

Flags

BackEureka Vacuum
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

Follow this guide to replace the brush roll on your Eureka 169 J 2-in-1 Quick-Up bagless stick vacuum cleaner.

Before beginning this guide, turn off the vacuum and unplug it from the outlet.

What you need

Step 1

              Brush roll

Unplug the vacuum from the outlet.

Unplug the vacuum from the outlet.

1024

Step 2

Use a damp paper towel to clean the bottom of the vacuum of any debris.

Use a damp paper towel to clean the bottom of the vacuum of any debris.

Step 3

Flip the vacuum over so the bottom is facing up.
Use a Phillips #2 screwdriver to remove the four 3.0 mm screws.
Use a Phillips #2 screwdriver to remove the two 4.2 mm screws.

Flip the vacuum over so the bottom is facing up.

Use a Phillips #2 screwdriver to remove the four 3.0 mm screws.

Use a Phillips #2 screwdriver to remove the two 4.2 mm screws.

Step 4

Pull the bottom and top cover of the brush roll compartment apart.
Internal components of the vacuum may fall out during this step, so keep track of where they are located for reassembly.

Pull the bottom and top cover of the brush roll compartment apart.

Internal components of the vacuum may fall out during this step, so keep track of where they are located for reassembly.

Step 5

Lift the brush roll out of the vacuum.
The brush roll is connected to two white placeholders on both left and right sides. To remove these, pull them away from the brush roll.

Lift the brush roll out of the vacuum.

The brush roll is connected to two white placeholders on both left and right sides. To remove these, pull them away from the brush roll.

Step 6

Thoroughly clean the inside of the vacuum with a damp paper towel and let it dry.

Thoroughly clean the inside of the vacuum with a damp paper towel and let it dry.

Step 7

To replace the brush roll, attach the two white placeholders on both ends of the brush roll and set them into the corresponding slots.
The slots are located on the left and right ends of the bottom cover.

To replace the brush roll, attach the two white placeholders on both ends of the brush roll and set them into the corresponding slots.

The slots are located on the left and right ends of the bottom cover.

Step 8

Reattach the cover and screw it back into place using a Phillips #2 screwdriver.
The two 4.2 mm Phillips #2 screws go in the two middle bottom holes.
The four 3.0 mm Phillips #2 screws go in the side holes.

Reattach the cover and screw it back into place using a Phillips #2 screwdriver.

The two 4.2 mm Phillips #2 screws go in the two middle bottom holes.

The four 3.0 mm Phillips #2 screws go in the side holes.

Plug in your device and test it to ensure that you have reassembled it correctly.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor

                    Mark Parala

Member since: 08/23/2022

157 Reputation

                                      1 Guide authored                  



                       Badges:
                       2

Team

                       CSU Los Angeles, Team 1-8, Briggs Fall 2022                        

                                                  Member of CSU Los Angeles, Team 1-8, Briggs Fall 2022 



                    CSULA-BRIGGS-F22S1G8                     


                                            1 Member                     


                                            1 Guide authored

Introduction#

What you need#

Team#

Introduction

What you need

Team