Difficulty

Easy

Steps

10

Time Required

                          10 minutes

Sections

3

  • Rechargeable Battery Pack
  • 2 steps
  • Case Assembly
  • 5 steps
  • Tuning Dial
  • 3 steps

Flags

1

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackEton FRX3

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

It’s important not to mix this up with the volume dial, as they are unique components and will not be interchangable.

What you need

Step 1

              Rechargeable Battery Pack
  • Pull the plastic tab on the battery compartment cover panel to loosen it, then pull the panel off.

Pull the plastic tab on the battery compartment cover panel to loosen it, then pull the panel off.

1024

Step 2

  • Disconnect the battery pack wires from the device and remove the battery pack.

Disconnect the battery pack wires from the device and remove the battery pack.

Step 3

              Case Assembly
  • On the bottom of the device case’s face are two T10 screws. Use a T10 Torx screwdriver to remove the two screws.

On the bottom of the device case’s face are two T10 screws. Use a T10 Torx screwdriver to remove the two screws.

Step 4

  • While using the T10 screwdriver, remove the two T10 screws on the back of the device’s case.

While using the T10 screwdriver, remove the two T10 screws on the back of the device’s case.

Step 5

  • Remove the two Phillips #00 screws located in the center of the back of the device.
  • You will need to use a thin shafted screwdriver or a female hexagonal bit that is found in the iFixit 54 bit toolkit to extend the reach of the Phillips #00 bit.

Remove the two Phillips #00 screws located in the center of the back of the device.

You will need to use a thin shafted screwdriver or a female hexagonal bit that is found in the iFixit 54 bit toolkit to extend the reach of the Phillips #00 bit.

Step 6

  • On the bottom of the device’s case there are two rubber feet. Pry the rubber feet off of the case.
  • Try to keep the adhesive on the rubber feet as clean as possible to insure that they can be reattached during reassembly.

On the bottom of the device’s case there are two rubber feet. Pry the rubber feet off of the case.

Try to keep the adhesive on the rubber feet as clean as possible to insure that they can be reattached during reassembly.

Step 7

  • Pull the two halves of the device’s case apart.
  • Take care when pulling the two halves apart. There are three cables that connect components of the device to the motherboard. Disconnect these cables in order to separate the two halves of the device’s case.

Pull the two halves of the device’s case apart.

Take care when pulling the two halves apart. There are three cables that connect components of the device to the motherboard. Disconnect these cables in order to separate the two halves of the device’s case.

Step 8

              Tuning Dial
  • Unplug the socket connection from the motherboard as shown in the image.

Unplug the socket connection from the motherboard as shown in the image.

Step 9

  • Remove the two 1 cm Phillips #0 screws that secure the tuning dial panel to the motherboard.

Remove the two 1 cm Phillips #0 screws that secure the tuning dial panel to the motherboard.

Step 10

  • Gently lift the dial upwards to remove it.

Gently lift the dial upwards to remove it.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Md Siamul Islam

Member since: 02/10/2016

420 Reputation

                                      4 Guides authored                  



                       Badges:
                       8







                                                        +5 more badges

Team

                       USF Tampa, Team 1-6, Nance Spring 2016                        

                                                  Member of USF Tampa, Team 1-6, Nance Spring 2016 



                    USFT-NANCE-S16S1G6                     


                                            4 Members                     


                                            13 Guides authored