Difficulty

Moderate

Steps

11

Time Required

                          5 minutes

Sections

4

  • Battery
  • 3 steps
  • Buttons
  • 5 steps
  • Etekcity Lasergrip 1080 Trigger Replacement
  • 1 step
  • Laser
  • 2 steps

Flags

0

  • BackEtekcity Lasergrip 1080

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Battery
  • Pull the battery cover away from the handle by gripping near the thumb groove.

Pull the battery cover away from the handle by gripping near the thumb groove.

1024

Step 2

  • Gently pull the battery out of the handle.
  • Excessive force could damage wires.

Gently pull the battery out of the handle.

Excessive force could damage wires.

Step 3

  • Disconnect the battery by pulling the connector away from it.
  • Positive first
  • Negative second
  • When replacing the battery, this order is reversed.

Disconnect the battery by pulling the connector away from it.

Positive first

Negative second

When replacing the battery, this order is reversed.

Step 4

              Buttons
  • Remove the battery cover from the device by pulling it straight out.

Remove the battery cover from the device by pulling it straight out.

Step 5

  • Using the plastic opening tool remove the front and rear yellow covers.
  • When removing the back cover, be careful not to lose the buttons as they are not connected.

Using the plastic opening tool remove the front and rear yellow covers.

When removing the back cover, be careful not to lose the buttons as they are not connected.

Step 6

  • Remove the two 3.1 mm Phillips #0 screws.

Remove the two 3.1 mm Phillips #0 screws.

Step 7

  • Pull the two halves apart.
  • Be careful not to lose any components on the inside.

Pull the two halves apart.

Be careful not to lose any components on the inside.

Step 8

  • Realign the buttons with the button terminals.
  • Red terminal to red button.
  • Orange terminal to orange button.
  • Yellow terminal to yellow button.

Realign the buttons with the button terminals.

Red terminal to red button.

Orange terminal to orange button.

Yellow terminal to yellow button.

Step 9

              Etekcity Lasergrip 1080 Trigger Replacement
  • Carefully pull the trigger out.
  • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.
  • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

Carefully pull the trigger out.

The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

Step 10

              Laser
  • Pull the motherboard out of its slot in the device.

Pull the motherboard out of its slot in the device.

Step 11

  • Use a soldering iron to melt the solder that holds the wires for the laser to the motherboard.
  • Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

Use a soldering iron to melt the solder that holds the wires for the laser to the motherboard.

Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 1 other contributor 


                    Patrick Crawford

Member since: 08/26/2015

741 Reputation

                                      6 Guides authored                  



                       Badges:
                       15







                                                        +12 more badges

Team

                       USF Tampa, Team 5-1, Blackwell Fall 2015                        

                                                  Member of USF Tampa, Team 5-1, Blackwell Fall 2015 



                    USFT-BLACKWELL-F15S5G1                     


                                            3 Members                     


                                            9 Guides authored