Difficulty

Moderate

Steps

6

Time Required

Suggest a time??

Sections

1

  • ESGE Magic Wand - Bamix disassemble
  • 6 steps

Flags

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

  • BackESGE Zauberstab - Bamix

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Remove top cover
  • Unplug the power cord and remove the cutter blade.
  • The top cover is fastened with two Torx TR10 security screws. These screws are different from normal Torx screws: they are equipped with a center pin. Use the right bit or screwdriver with center hole.
  • Remove two Torx TR10 screws.
  • Carefully lift off the cover. It is latched at the front.

Unplug the power cord and remove the cutter blade.

The top cover is fastened with two Torx TR10 security screws. These screws are different from normal Torx screws: they are equipped with a center pin. Use the right bit or screwdriver with center hole.

Remove two Torx TR10 screws.

Carefully lift off the cover. It is latched at the front.

1024

Step 2

  • This is what it looks like under the cover.
  • Slide out the two buttons and the small circuit board. The buttons are only snapped in.

This is what it looks like under the cover.

Slide out the two buttons and the small circuit board. The buttons are only snapped in.

Step 3

  • The handle is fastened with a Torx T8 machine screw and a Torx T8 plastic screw. You will need a long screwdriver.
  • Remove two Torx T8 screws.

The handle is fastened with a Torx T8 machine screw and a Torx T8 plastic screw. You will need a long screwdriver.

Remove two Torx T8 screws.

Step 4

  • Unclip the handle from one side.
  • Unthread the cable, the buttons and the board.
  • The motor ist exposed. However, it is not yet completely accessible, since the lower plastic housing part cannot yet be slid over the bell. The bell must first be removed.

Unclip the handle from one side.

Unthread the cable, the buttons and the board.

The motor ist exposed. However, it is not yet completely accessible, since the lower plastic housing part cannot yet be slid over the bell. The bell must first be removed.

Step 5

  • First try If the bell can be unscrewed. It is fastened with a left-hand thread, so turn it in the “wrong direction”, clockwise, to loosen it.
  • Pull on the knife to remove it
  • The bell sits probably quite tight, as it should not come loose during normal operation. When reassembling, glue it in place with a few drops of fluid threadlocker, if needed.
  • If it does not come off easily, then slide the lower plastic part towards the bell and clamp the motor in a vice. Do not tighten the vice very much, the motor is sensitive.
  • Use a long screwdriver as a lever between the bell and the shaft. Then carefully unscrew the bell. Reminder: the wrong way round, i.e. clockwise.
  • Pay attention to the washer between the shaft and the bell, do not lose it.

First try If the bell can be unscrewed. It is fastened with a left-hand thread, so turn it in the “wrong direction”, clockwise, to loosen it.

Pull on the knife to remove it

The bell sits probably quite tight, as it should not come loose during normal operation. When reassembling, glue it in place with a few drops of fluid threadlocker, if needed.

If it does not come off easily, then slide the lower plastic part towards the bell and clamp the motor in a vice. Do not tighten the vice very much, the motor is sensitive.

Use a long screwdriver as a lever between the bell and the shaft. Then carefully unscrew the bell. Reminder: the wrong way round, i.e. clockwise.

Pay attention to the washer between the shaft and the bell, do not lose it.

Step 6

  • Pull off the lower case over the shaft.

Pull off the lower case over the shaft.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

        These translators are helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

VauWeh

oldturkey03

Author

                                      with 2 other contributors 


                    VauWeh

Member since: 10/19/2015

160,518 Reputation

                                      211 Guides authored                  



                       Badges:
                       41







                                                        +38 more badges