Difficulty
Moderate
Steps
11
Time Required
25 - 45 minutes
Sections
2
- Lamp
- 4 steps
- Feet
- 7 steps
Flags
Needs Better Images
Better photos will improve this guide. Help out by taking, editing, or uploading new ones!
Needs More Images
A few more images would make this guide’s procedures crystal clear.
BackEpson VS250
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
What you need
Step 1
Lamp
- Place the projector on a flat surface.
- Orient the projector so that the the word “Epson” is facing you.
- Use Phillips #1 screwdriver to loosen the 10 mm screw on the top right corner of the projector.
- The screw does not need to come all the way out.
Place the projector on a flat surface.
Orient the projector so that the the word “Epson” is facing you.
Use Phillips #1 screwdriver to loosen the 10 mm screw on the top right corner of the projector.
The screw does not need to come all the way out.
1024
Step 2
- Slide the cover to the right and lift the cover up and out to remove.
Slide the cover to the right and lift the cover up and out to remove.
Step 3
- Use a Phillips #1 screwdriver to loosen the two 10 mm screws that hold the lamp in place.
- The two 10 mm screws do not need to come all the way out. Just ensure they are loose.
Use a Phillips #1 screwdriver to loosen the two 10 mm screws that hold the lamp in place.
The two 10 mm screws do not need to come all the way out. Just ensure they are loose.
Step 4
- After loosening both screws, remove the lamp from the projector by pulling it up and out.
After loosening both screws, remove the lamp from the projector by pulling it up and out.
Step 5
Feet
- Use a Phillips #1 screwdriver to remove the three 6 mm screws that hold the side portion of the projector in place.
Use a Phillips #1 screwdriver to remove the three 6 mm screws that hold the side portion of the projector in place.
Step 6
- Use a Phillips #1 screwdriver to remove the single 10 mm screw that is holding the side cover of the projector in place.
Use a Phillips #1 screwdriver to remove the single 10 mm screw that is holding the side cover of the projector in place.
Step 7
- Use a Phillips #1 screwdriver to remove the two 10.00mm screws that are holding the side cover of the projector in place.
Use a Phillips #1 screwdriver to remove the two 10.00mm screws that are holding the side cover of the projector in place.
Step 8
- Flip the projector so that it lays upside down.
- Using a Phillips #1 screwdriver, remove the three 10 mm screws that secure the side portion of the projector.
Flip the projector so that it lays upside down.
Using a Phillips #1 screwdriver, remove the three 10 mm screws that secure the side portion of the projector.
Step 9
- Remove the front cover from the projector by pulling it off.
Remove the front cover from the projector by pulling it off.
Step 10
- Twist the two feet in the counterclockwise direction until both feet are full extended to their maximum lengths.
Twist the two feet in the counterclockwise direction until both feet are full extended to their maximum lengths.
Step 11
- Place the tweezers into the hole where the foot is connected.
- Use one of your hands to squeeze the tweezers on the top of the foot. Use your free hand to wiggle the bottom of the foot while pulling outward to remove it.
- Repeat this step for any additional feet.
Place the tweezers into the hole where the foot is connected.
Use one of your hands to squeeze the tweezers on the top of the foot. Use your free hand to wiggle the bottom of the foot while pulling outward to remove it.
Repeat this step for any additional feet.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 2 other contributors
Warren Cutlip
Member since: 09/28/2021
604 Reputation
5 Guides authored
Badges:
7
+4 more badges
Team
Clemson, Team 4-2, Hunter Fall 2021
Member of Clemson, Team 4-2, Hunter Fall 2021
CLEM-HUNTER-F21S4G2
5 Members
5 Guides authored
