Difficulty

Easy

Steps

7

Time Required

                          10 - 30 minutes

Sections

1

  • Shell
  • 7 steps

Flags

2

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackEpson VS240

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Shell
  • Using the Phillips #2 screwdriver, loosen the single captive screw on the left side of the projector.
  • The captive screw will loosen, but it cannot be fully removed.
  • Slide the panel off and remove it from the device.

Using the Phillips #2 screwdriver, loosen the single captive screw on the left side of the projector.

The captive screw will loosen, but it cannot be fully removed.

Slide the panel off and remove it from the device.

1024

Step 2

  • Use the Phillips #2 screwdriver to remove the three 5 mm screws.
  • Using the same Phillips #2 screwdriver, remove the single 8 mm silver screw.

Use the Phillips #2 screwdriver to remove the three 5 mm screws.

Using the same Phillips #2 screwdriver, remove the single 8 mm silver screw.

Step 3

  • Use a Phillips #1 screwdriver to remove the two 10 mm silver screws from the bottom of the device.

Use a Phillips #1 screwdriver to remove the two 10 mm silver screws from the bottom of the device.

Step 4

  • Use a Phillips #1 screwdriver to remove the single 10 mm screw where the panel was removed in Step 1.
  • Remove the white back plate from the device.

Use a Phillips #1 screwdriver to remove the single 10 mm screw where the panel was removed in Step 1.

Remove the white back plate from the device.

Step 5

  • Flip the projector over so that the underside (side with the feet) is facing you.
  • Use a Phillips #1 screwdriver to remove five 10 mm screws on the underside of projector.
  • Using the same Phillips #1 screwdriver, remove a single 10 mm screw in the center hole.
  • You may need to use a screwdriver extender to reach the single screw.

Flip the projector over so that the underside (side with the feet) is facing you.

Use a Phillips #1 screwdriver to remove five 10 mm screws on the underside of projector.

Using the same Phillips #1 screwdriver, remove a single 10 mm screw in the center hole.

You may need to use a screwdriver extender to reach the single screw.

Step 6

  • Use a Phillips #1 screwdriver to remove two 10 mm screws from the openings on each side of the air filter, on the topside of the projector.
  • You may need to use a screwdriver extender to reach the two screws.
  • Using the same Phillips #1 screwdriver, remove the two 10 mm screws where the white panel was removed on the topside of the projector in Step 1.

Use a Phillips #1 screwdriver to remove two 10 mm screws from the openings on each side of the air filter, on the topside of the projector.

You may need to use a screwdriver extender to reach the two screws.

Using the same Phillips #1 screwdriver, remove the two 10 mm screws where the white panel was removed on the topside of the projector in Step 1.

Step 7

  • Be careful when removing the top cover of projector as there is as white ribbon cable connecting it to the motherboard.
  • Gently lift top cover and place it on its top next to the projector so that the ribbon has no tension on it.
  • Gently pull the brown tape connecting the cable to the motherboard and then remove the shell from the device.

Be careful when removing the top cover of projector as there is as white ribbon cable connecting it to the motherboard.

Gently lift top cover and place it on its top next to the projector so that the ribbon has no tension on it.

Gently pull the brown tape connecting the cable to the motherboard and then remove the shell from the device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 3 other contributors 


                    Gerard Huber

Member since: 09/28/2021

329 Reputation

                                      2 Guides authored                  



                       Badges:
                       6







                                                        +3 more badges

Team

                       Clemson, Team 5-3, Hunter Fall 2021                        

                                                  Member of Clemson, Team 5-3, Hunter Fall 2021 



                    CLEM-HUNTER-F21S5G3                     


                                            5 Members                     


                                            6 Guides authored