Difficulty

Moderate

Steps

9

Time Required

Suggest a time??

Sections

2

  • Motherboard
  • 7 steps
  • Motor
  • 2 steps

Flags

1

Action Shots

Be an action hero! This guide needs images that better demonstrate how to perform specific actions.

  • BackEpson Stylus NX230

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

Introduction

What you need

Step 1

              Motherboard
  • Check to make sure the printer is unplugged to prevent electric shock.

Check to make sure the printer is unplugged to prevent electric shock.

1024

Step 2

  • Align your printer so that the front buttons face to the right.
  • Remove the 3mm Phillips #2 screw in the hole in the top left corner. This screw attaches the side panel to the printer.
  • Store the screws in a safe place so you can access them later.

Align your printer so that the front buttons face to the right.

Remove the 3mm Phillips #2 screw in the hole in the top left corner. This screw attaches the side panel to the printer.

Store the screws in a safe place so you can access them later.

Step 3

  • Flip and remove the top of the printer up so that you can see the inside.
  • There is a white strip in the top right corner of the printer called the ribbon cable.
  • Make sure that the ribbon cable does not detach from the printer to prevent damaging the connection.

Flip and remove the top of the printer up so that you can see the inside.

There is a white strip in the top right corner of the printer called the ribbon cable.

Make sure that the ribbon cable does not detach from the printer to prevent damaging the connection.

Step 4

  • Align the printer so the front button panel faces to the right.
  • Remove the 3mm Phillips #2 screw on the side of the printer in the top left corner.
  • Store the screw in a safe place so you can access it later.

Align the printer so the front button panel faces to the right.

Remove the 3mm Phillips #2 screw on the side of the printer in the top left corner.

Store the screw in a safe place so you can access it later.

Step 5

  • Take the right side of the bar of plastic that runs across the top of the inside of the printer and push it towards the left side of the printer.
  • Take the left side of the bar and push it to the left and then to the right.

Take the right side of the bar of plastic that runs across the top of the inside of the printer and push it towards the left side of the printer.

Take the left side of the bar and push it to the left and then to the right.

Step 6

  • Using your hands, detach the side panel from the printer.
  • Take extra care with the locking mechanisms, which help keep the side panel on the printer.
  • You may need to use the plastic opening tools to pry apart the locking mechanisms.

Using your hands, detach the side panel from the printer.

Take extra care with the locking mechanisms, which help keep the side panel on the printer.

You may need to use the plastic opening tools to pry apart the locking mechanisms.

Step 7

  • Remove the two 3mm Phillips #2 screws attaching motherboard to the printer.
  • Store the screws in a safe place so you can access them later.
  • The motherboard can now be removed from the printer.

Remove the two 3mm Phillips #2 screws attaching motherboard to the printer.

The motherboard can now be removed from the printer.

Step 8

              Motor
  • Remove the four 3mm Phillips #2 screws attaching the motor to the printer.
  • Store the screws in a safe place so you can access them later.

Remove the four 3mm Phillips #2 screws attaching the motor to the printer.

Step 9

  • Place the printer on it’s side so that the motherboard’s location is facing up.
  • Push the motor up and out of the hole that it is in.
  • The motor will slide out of the hole at the top after that.

Place the printer on it’s side so that the motherboard’s location is facing up.

Push the motor up and out of the hole that it is in.

The motor will slide out of the hole at the top after that.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 5 other contributors 


                    Kimberly Pugel

Member since: 04/07/2014

389 Reputation

                                      3 Guides authored                  



                       Badges:
                       7







                                                        +4 more badges

Team

                       Cal Poly, Team 6-1, Forte Spring 2014                        

                                                  Member of Cal Poly, Team 6-1, Forte Spring 2014 



                    CPSU-FORTE-S14S6G1                     


                                            4 Members                     


                                            5 Guides authored