Difficulty

Difficult

Steps

8

Time Required

                          30 - 40 minutes

Sections

2

  • Disassembling Epson PPC650 Camera Casing
  • 5 steps
  • Accessing the old screen and installing the new screen
  • 3 steps

Flags

5

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

In Progress

This guide is a work in progress. Reload periodically to see the latest changes!

Markup Mishap

This guide needs better markups. Help out by correcting or making some markup annotations.

Needs More Images

A few more images would make this guide’s procedures crystal clear.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackEpson PhotoPC 650

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Edit

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Disassembling Epson PPC650 Camera Casing
  • Make sure the camera is turned off here.
  • Remove batteries from the battery compartment located on the bottom of the camera
  • Remove SD card for the card reader compartment located on the flat side (left side) of the camera

Make sure the camera is turned off here.

Remove batteries from the battery compartment located on the bottom of the camera

Remove SD card for the card reader compartment located on the flat side (left side) of the camera

1024

Step 2

  • Remove 2 screws on the rounded side of the camera wisdom here.

Remove 2 screws on the rounded side of the camera wisdom here.

Step 3

  • Remove 3 screws on the flat side of the camera
  • All silver screws go into the side of the camera that is silver
  • All black screws go into the side of the camera that is black

Remove 3 screws on the flat side of the camera

All silver screws go into the side of the camera that is silver

All black screws go into the side of the camera that is black

Step 4

  • Remove 4 screws from the bottom of the camera
  • All silver screws go into the side of the camera that is silver
  • All black screws go into the side of the camera that is black

Remove 4 screws from the bottom of the camera

Step 5

  • Separate the front and back pieces of the cameras plastic casing using a spudgerm here.
  • WARNING: When pulling the front plastic casing, be careful of the wire that are connected to the aperture control
  • Use minimal force so that the plastic casing does not break
  • When separating the small silver sliding indicator for view/off/playback may fall out
  • The plastic viewing window located on the top of the camera may also become lose and fall out

Separate the front and back pieces of the cameras plastic casing using a spudgerm here.

WARNING: When pulling the front plastic casing, be careful of the wire that are connected to the aperture control

Use minimal force so that the plastic casing does not break

When separating the small silver sliding indicator for view/off/playback may fall out

The plastic viewing window located on the top of the camera may also become lose and fall out

Step 6

              Accessing the old screen and installing the new screen
  • Remove copper sheet from the front paneling and back.
  • You will need to use a spudger to unsolder the copper paneling
  • Use the spudger to separate the back circuit board from the camera

Remove copper sheet from the front paneling and back.

You will need to use a spudger to unsolder the copper paneling

Use the spudger to separate the back circuit board from the camera

Step 7

  • The picture viewing screen is glued to the backing as well as wired in with pink and white wires.
  • Exert minimal force required to pull the screen loose from the camera
  • Remove the pink and white wiring from the internal paneling. These wires are soldered in
  • Remove the orange data hookup cable which feeds into the back circuit board

The picture viewing screen is glued to the backing as well as wired in with pink and white wires.

Exert minimal force required to pull the screen loose from the camera

Remove the pink and white wiring from the internal paneling. These wires are soldered in

Remove the orange data hookup cable which feeds into the back circuit board

Step 8

  • Once all wires have been detached and the old screen has been removed place the new screen into the camera.
  • Insert data hookup into the back of the camera and into the new screen
  • Re-solder the new pink and white wire onto the internal circuit board

Once all wires have been detached and the old screen has been removed place the new screen into the camera.

Insert data hookup into the back of the camera and into the new screen

Re-solder the new pink and white wire onto the internal circuit board

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors 


                    Anne

Member since: 02/12/2013

101 Reputation

                                      1 Guide authored                  



                       Badges:
                       3

Team

                       Ohio State, Team 1-5, Buehl Spring 2013                        

                                                  Member of Ohio State, Team 1-5, Buehl Spring 2013 



                    OSU-BUEHL-S13S1G5                     


                                            4 Members                     


                                            3 Guides authored