Difficulty
Difficult
Steps
28
Time Required
1 - 2 hours
Sections
4
- Projector Lamp
- 3 steps
- Wireless connection board
- 10 steps
- Speaker
- 4 steps
- Exhaust Fan
- 11 steps
Flags
0
BackEpson Home Cinema 2150
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
It is located inside the projector on the same row as the projector lens, all the way to the left, next to the power supply.
What you need
Step 1
Projector Lamp
- Disconnect and cool the device to room temperature. Failure to do so may result in electric shock or minor burns.
- Orient the Epson Home Cinema 2150 so that the large indented panel faces your direction.
- Unscrew the single 6mm Phillips#2 holding screw from the access panel.
- Slide the panel horizontally, then lift up to remove the access panel.
Disconnect and cool the device to room temperature. Failure to do so may result in electric shock or minor burns.
Orient the Epson Home Cinema 2150 so that the large indented panel faces your direction.
Unscrew the single 6mm Phillips#2 holding screw from the access panel.
Slide the panel horizontally, then lift up to remove the access panel.
1024
Step 2
- Loosen and remove the two screws holding the lamp.
- Remove two 9 mm Phillips #2 screws.
Loosen and remove the two screws holding the lamp.
Remove two 9 mm Phillips #2 screws.
Step 3
- Using four fingers, pull upwards on the lamp’s plastic casing.
- You may feel some resistance when pulling the lamp.
Using four fingers, pull upwards on the lamp’s plastic casing.
You may feel some resistance when pulling the lamp.
Step 4
Wireless connection board
- Remove the air filter cover. Grip the piece with two fingers above and below at the center.
- Grab the air filter from the protruding tab and pull the filter out.
Remove the air filter cover. Grip the piece with two fingers above and below at the center.
Grab the air filter from the protruding tab and pull the filter out.
Step 5
- From the back of the projector remove three 6 mm Phillips #1 screws.
From the back of the projector remove three 6 mm Phillips #1 screws.
Step 6
- From the device’s underside, remove eleven 9.5 mm Phillips #1 screws.
- Remove two 6 mm Phillips #1 screws.
- Pull off remaining plastic molding.
From the device’s underside, remove eleven 9.5 mm Phillips #1 screws.
Remove two 6 mm Phillips #1 screws.
Pull off remaining plastic molding.
Step 7
- From the lamp access slot, remove four 9.5 mm Philips #1 screws
From the lamp access slot, remove four 9.5 mm Philips #1 screws
Step 8
- From the filter slot, unscrew two 9.5 mm #1 screws.
From the filter slot, unscrew two 9.5 mm #1 screws.
Step 9
- Partially lift the top portion of the device housing.
- Lifting too far or too hard may damage any cables between the housing and the motherboard.
Partially lift the top portion of the device housing.
Lifting too far or too hard may damage any cables between the housing and the motherboard.
Step 10
- Disconnect the ribbon cable from the motherboard.
- Ribbon cables are delicate. To avoid unnecessary stress to the cable, pull on the cable with the flat surface of two fingers.
Disconnect the ribbon cable from the motherboard.
Ribbon cables are delicate. To avoid unnecessary stress to the cable, pull on the cable with the flat surface of two fingers.
Step 11
- Remove three 5 mm Phillips #1 screws.
Remove three 5 mm Phillips #1 screws.
Step 12
- Press on the metal connector and firmly pull on the remaining ribbon cable.
Press on the metal connector and firmly pull on the remaining ribbon cable.
Step 13
- Pull the clips on the case with two fingers on opposite ends and remove the case.
Pull the clips on the case with two fingers on opposite ends and remove the case.
Step 14
Speaker
- Pull up on the rear panel retaining clip.
- Pull the rear panel away from the device to remove.
Pull up on the rear panel retaining clip.
Pull the rear panel away from the device to remove.
Step 15
- Disconnect the speaker wire from the motherboard.
- Pull up at the end of the wire when removing the connector.
Disconnect the speaker wire from the motherboard.
Pull up at the end of the wire when removing the connector.
Step 16
- Unwind the speaker wire through the metal chassis.
Unwind the speaker wire through the metal chassis.
Step 17
- Remove two 6mm Phillips #1 screws.
- The speaker will fall out once screws are removed.
Remove two 6mm Phillips #1 screws.
The speaker will fall out once screws are removed.
Step 18
Exhaust Fan
- Remove two 6 mm Phillips #1 screws.
- Remove two 5 mm Phillips #1 screws.
Remove two 5 mm Phillips #1 screws.
Step 19
- Disconnect a total of 10 motherboard connections.
- Disconnect wires individually to avoid potential damage to the motherboard or the wires.
Disconnect a total of 10 motherboard connections.
Disconnect wires individually to avoid potential damage to the motherboard or the wires.
Step 20
- Press on the metal connector and firmly pull to remove the remaining ribbon cable.
- Ribbon cables are delicate. To avoid unnecessary stress to the cable, pull on the cable with the flat surface of two fingers.
Press on the metal connector and firmly pull to remove the remaining ribbon cable.
Step 21
- Remove twelve 5 mm Phillips #1 screws.
- Using both hands, carefully lift the first half of the motherboard.
Remove twelve 5 mm Phillips #1 screws.
Using both hands, carefully lift the first half of the motherboard.
Step 22
- Disconnect the three brown ribbon connectors from the board.
- Ribbon cables are delicate. To avoid unnecessary stress to the cable, pull on the cable with the flat surface of a finger.
- Remove four 5 mm Phillips #1 screws.
- Remove two 3 mm Phillips #1 screws.
- Pull upwards on the motherboard to remove it from the projector.
Disconnect the three brown ribbon connectors from the board.
Ribbon cables are delicate. To avoid unnecessary stress to the cable, pull on the cable with the flat surface of a finger.
Remove four 5 mm Phillips #1 screws.
Remove two 3 mm Phillips #1 screws.
Pull upwards on the motherboard to remove it from the projector.
Step 23
- Remove the 7.5 mm Phillips #1 screw.
- Remove two 6 mm Phillips #1 screws.
- Set the black plastic lens sliders to the side.
Remove the 7.5 mm Phillips #1 screw.
Set the black plastic lens sliders to the side.
Step 24
- Remove five 9.5 mm Phillips #1 screws.
- Remove one 6.0 mm Phillips #2 screw.
- This screw is located to the right of the rear 9.5 mm screw.
- Remove the metal bracket by pulling upwards on its sides.
Remove five 9.5 mm Phillips #1 screws.
Remove one 6.0 mm Phillips #2 screw.
This screw is located to the right of the rear 9.5 mm screw.
Remove the metal bracket by pulling upwards on its sides.
Step 25
- Remove the 9.5 mm Phillips #1 screw located behind the power supply.
- Unwind the fan cable from the power supply for better access to the screw.
- Remove the 10 mm Phillips #1 screw.
Remove the 9.5 mm Phillips #1 screw located behind the power supply.
Unwind the fan cable from the power supply for better access to the screw.
Remove the 10 mm Phillips #1 screw.
Step 26
- Move the fan cable to the side for clear access to the sensor below it.
- Using pliers, pull upwards on the white sensor to remove it from the fan assembly.
Move the fan cable to the side for clear access to the sensor below it.
Using pliers, pull upwards on the white sensor to remove it from the fan assembly.
Step 27
- Remove two 9.5mm Phillips #1 screws.
Remove two 9.5mm Phillips #1 screws.
Step 28
- Carefully lift upwards on the fan assembly to remove the fan from the projector.
Carefully lift upwards on the fan assembly to remove the fan from the projector.
To reassemble your device, follow these instructions in reverse order.
Cancel: I did not complete this guide.
Author
with 3 other contributors
Luis Garcia
Member since: 09/26/2022
577 Reputation
4 Guides authored
Badges:
5
+2 more badges
Team
CSU Los Angeles, Team 6-2, Adachi Fall 2022
Member of CSU Los Angeles, Team 6-2, Adachi Fall 2022
CSULA-ADACHI-F22S6G2
4 Members
5 Guides authored
