Difficulty
Easy
Steps
10
Time Required
5 - 10 minutes
Sections
1
- Filter
- 10 steps
Flags
0
BackKitchen Appliance
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications
Introduction
It is important to do this replacement since we would want to keep your water source as clean as possible. The filter should be always replace in 6-9 months. You can always make sure by marking the dates down.
Make sure you have prepared a brand new filter for steps 7 and 8 to replace the old one.
Before beginning, you might want to clean up the surroundings. You don’t want anything getting in your water filter machine.
What you need
Step 1
Filter
- Turn off and unplug the machine before cleaning it.
- Clean the machine with a damp cloth or paper towel.
- Make sure nothing dirty will get in the machine during the process.
Turn off and unplug the machine before cleaning it.
Clean the machine with a damp cloth or paper towel.
Make sure nothing dirty will get in the machine during the process.
1024
Step 2
- Open the filter door by pushing the “Push” button.
Open the filter door by pushing the “Push” button.
Step 3
- Turn the ring at the bottom of the filter to the left until you hear a “click”.
Turn the ring at the bottom of the filter to the left until you hear a “click”.
Step 4
- Remove the ring for now.
Remove the ring for now.
Step 5
- Lift up the old filter and discard or recycle appropriately.
- Some water might be dripping out from the bottom of it. Have a towel ready to clean it up.
Lift up the old filter and discard or recycle appropriately.
Some water might be dripping out from the bottom of it. Have a towel ready to clean it up.
Step 6
- Remove the two black rubber rings.
- They are NOT components of the machine. The new filter you have prepared should come with new ones.
Remove the two black rubber rings.
They are NOT components of the machine. The new filter you have prepared should come with new ones.
Step 7
- Put your new filter in it.
- Make sure that the two holes match the two popped-out parts from the filter.
- The one that is bigger should be on the middle and the smaller one should be on the side.
- This filter should be the new one that you have prepared and NOT the one that is removed from Step 5.
Put your new filter in it.
Make sure that the two holes match the two popped-out parts from the filter.
The one that is bigger should be on the middle and the smaller one should be on the side.
This filter should be the new one that you have prepared and NOT the one that is removed from Step 5.
Step 8
- Put the ring component back in.
- Turn it to your right until you hear a click.
- Make sure it is successfully locked in.
Put the ring component back in.
Turn it to your right until you hear a click.
Make sure it is successfully locked in.
Step 9
- Turn the filter back on.
- Press the “Reset Switch”
- “FILTER RESET” should be shown on the display.
Turn the filter back on.
Press the “Reset Switch”
“FILTER RESET” should be shown on the display.
Step 10
- Attach the filter door.
- There are three holes to slide the door edge into.
- And push the “push” button to close it.
Attach the filter door.
There are three holes to slide the door edge into.
And push the “push” button to close it.
To change another filter, simply just follow the instructions once more.
Cancel: I did not complete this guide.
Author
with 1 other contributor
Edwin Ng
Member since: 09/12/2021
181 Reputation
1 Guide authored
Badges:
2
Team
York University, Team 1-16, O'Regan Fall 2021
Member of York University, Team 1-16, O'Regan Fall 2021
YORK-O'REGAN-F21S1G16
1 Member
1 Guide authored
