Ematic Genesis Battery Replacement Repair Guide

Difficulty

Moderate

Steps

Time Required

                          5 minutes

Sections

Ematic Genesis Casing
3 steps
Battery
3 steps

Flags

BackEmatic Genesis
Full Screen
Options
History
Save to Favorites
Download PDF
Edit
Translate
Get Shareable Link
Embed This Guide
Notify Me of Changes
Stop Notifications

Introduction

What you need

Step 1

              Ematic Genesis Casing

Unscrew the two (2) 1.3mm Phillips #00 screws found on the bottom edge of the tablet, where the power and volume buttons are located.

Unscrew the two (2) 1.3mm Phillips #00 screws found on the bottom edge of the tablet, where the power and volume buttons are located.

1024

Step 2

Insert plastic opening tool into the edge between the screen plate and the back plate to create a separation between the casings.
Insert the flat end of the spudger next to the plastic opening tool and carefully pry the edges apart. Continue this all around the edges until the casings separate.
There may be cracking sounds when prying them apart. If carefully done, this is only the locks coming apart and is not harmful.
Be careful when separating the two plates as they are connected by the speaker wires and could be disconnected during this process.

Insert plastic opening tool into the edge between the screen plate and the back plate to create a separation between the casings.

Insert the flat end of the spudger next to the plastic opening tool and carefully pry the edges apart. Continue this all around the edges until the casings separate.

There may be cracking sounds when prying them apart. If carefully done, this is only the locks coming apart and is not harmful.

Be careful when separating the two plates as they are connected by the speaker wires and could be disconnected during this process.

Step 3

Remove back plate from screen plate and lay both down flat next to each other.
Be careful when separating the two plates as they are connected by the speaker wires and could be disconnected during this process.

Remove back plate from screen plate and lay both down flat next to each other.

Step 4

              Battery

Lift up the two pieces of tape holding the copper plate and the connector ribbon to the battery. Gently hold or place away from the battery.

Lift up the two pieces of tape holding the copper plate and the connector ribbon to the battery. Gently hold or place away from the battery.

Step 5

Using a plastic card, gently break the adhesive that holds the battery to the metal screen plate.
The battery is very bendable. Although it may not be working, there are still dangerous contents inside batteries.

Using a plastic card, gently break the adhesive that holds the battery to the metal screen plate.

The battery is very bendable. Although it may not be working, there are still dangerous contents inside batteries.

Step 6

If replacing the battery, disconnect the wires that connect the battery to the motherboard.
If not replacing the battery, do NOT disconnect the wires.
To reconnect the new battery, a soldering kit will be necessary. Use the iFixit soldering guide to gain further information on how to complete this step.
How To Solder and Desolder Connections

If replacing the battery, disconnect the wires that connect the battery to the motherboard.

If not replacing the battery, do NOT disconnect the wires.

To reconnect the new battery, a soldering kit will be necessary. Use the iFixit soldering guide to gain further information on how to complete this step.

How To Solder and Desolder Connections

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 4 other contributors

                    Justin Rohrman

Member since: 03/23/2015

745 Reputation

                                      6 Guides authored                  



                       Badges:
                       12







                                                        +9 more badges

Team

                       Baylor, Team 4-3, Williams Spring 2015                        

                                                  Member of Baylor, Team 4-3, Williams Spring 2015 



                    BU-WILLIAMS-S15S4G3                     


                                            3 Members                     


                                            12 Guides authored

Danny Abreu Victoriano - Sep 1, 2016

tienen el firmware disponible?

Introduction#

What you need#

Team#

Introduction

What you need

Team