Difficulty

Moderate

Steps

13

Time Required

                          1 hour

Sections

1

  • Electrolux LTE12 - Washing Machine Disassembly
  • 13 steps

Flags

3

Bullets!

Better coordination with markups and the color/type of bullets will help make this guide more clear!

Member-Contributed Guide

An awesome member of our community made this guide. It is not managed by iFixit staff.

Better Introduction

Improve this guide by completing or revising its introduction.

  • BackWashing Machine - Electrolux LTE12

  • Full Screen

  • Options

  • History

  • Save to Favorites

  • Download PDF

  • Translate

  • Get Shareable Link

  • Embed This Guide

  • Notify Me of Changes

  • Stop Notifications

What you need

Step 1

              Electrolux LTE12 - Washing Machine Disassembly
  • Unplug the wall outlet.
  • Release the water hose.
  • Loosen the 4 Phillips screws at the top and 2 1/4 screws below.

Unplug the wall outlet.

Release the water hose.

Loosen the 4 Phillips screws at the top and 2 1/4 screws below.

1024

Step 2

  • Fasten the lid of the washing machine with a large crepe tape. Do not open when removing the top of the machine.
  • There is no need to remove the glass cover to remove the top of the machine.

Fasten the lid of the washing machine with a large crepe tape. Do not open when removing the top of the machine.

There is no need to remove the glass cover to remove the top of the machine.

Step 3

  • Open the top of the washer. Lift the back first. And then the front.
  • Grip the top of the machine with care. Take care not to drop and break the cover glass.
  • Release the power cord and hose clips from the pressure switch.

Open the top of the washer. Lift the back first. And then the front.

Grip the top of the machine with care. Take care not to drop and break the cover glass.

Release the power cord and hose clips from the pressure switch.

Step 4

  • Remove the Phillips screw.
  • Remove the two plastic fasteners.
  • Remove the protective cap (semi-transparent) on the left side.

Remove the Phillips screw.

Remove the two plastic fasteners.

Remove the protective cap (semi-transparent) on the left side.

Step 5

  • Remove the two Phillips screws.
  • Remove the protective cap (semi-transparent) on the right side.

Remove the two Phillips screws.

Remove the protective cap (semi-transparent) on the right side.

Step 6

  • To loosen the Control Panel cover, loosen the two Phillips screws. (Left side).

To loosen the Control Panel cover, loosen the two Phillips screws. (Left side).

Step 7

  • To loosen the Control Panel cover, also loosen the two Phillips screws on the right side.

To loosen the Control Panel cover, also loosen the two Phillips screws on the right side.

Step 8

  • Carefully lift the cover of the Control Panel. In this photo, the glass cover was removed to enlarge the image.

Carefully lift the cover of the Control Panel. In this photo, the glass cover was removed to enlarge the image.

Step 9

  • If there is a need to replace the Power Circuit Board, carefully pull out the program select button.
  • And then loosen the two Phillips screws.
  • Disconnect the cables carefully.

If there is a need to replace the Power Circuit Board, carefully pull out the program select button.

And then loosen the two Phillips screws.

Disconnect the cables carefully.

Step 10

  • To remove the circuit board from the Panel buttons, remove the three Phillips screws. Disconnect the cable carefully.
  • When removing the circuit board from the buttons, be aware of the three button springs.

To remove the circuit board from the Panel buttons, remove the three Phillips screws. Disconnect the cable carefully.

When removing the circuit board from the buttons, be aware of the three button springs.

Step 11

  • If you need to replace any components on the button circuit board, loosen the three Phillips screws to remove the acrylic shield.
  • The problem with my machine was the power button. With a soldering iron and a sucker, I switched on the power switch.

If you need to replace any components on the button circuit board, loosen the three Phillips screws to remove the acrylic shield.

The problem with my machine was the power button. With a soldering iron and a sucker, I switched on the power switch.

Step 12

  • To change the pressure switch, cut the clamp and remove the
  • Disconnect wires.
  • And then loosen the two Phillips screws.

To change the pressure switch, cut the clamp and remove the

Disconnect wires.

Step 13

  • To assemble the Washing Machine, follow the same procedure, in the reverse order.

To assemble the Washing Machine, follow the same procedure, in the reverse order.

To reassemble your device, Follow these instructions in reverse order.

Cancel: I did not complete this guide.

                                                                                      2 other people completed this guide.                                             


        irlanda is helping us fix the world!      Want to contribute?      Start translating ›

Special thanks to these translators:

100%

irlanda

Author

                                      with 1 other contributor 


                    Jose Gustavo Abreu Murta

Member since: 07/06/2010

4,261 Reputation

                                      8 Guides authored                  



                       Badges:
                       27







                                                        +24 more badges

ramiro34676067 - Sep 19, 2022

Reply

muito boa a espricação