Eightarc Fusion Usb Cable Replacement Repair Guide

Difficulty

Very easy

Steps

5

Time Required

                          5 - 10 minutes            

Sections

1

• USB Cable
• 5 steps

Flags

Slice and Dice

The steps in this guide should be split up and made into a series of prerequisite guides.

• BackEightarc Fusion

• Full Screen

• Options

• History

• Save to Favorites

• Download PDF

• Edit

• Translate

• Get Shareable Link

• Embed This Guide

• Notify Me of Changes

• Stop Notifications

Introduction

Warning: Use caution when placing the joystick face down on the table. The joystick can crack if placed down too hard. Be sure to gently turn the device over and place it face down. It can be helpful to balance the other side of the device to distribute the weight.

What you need

Step 1

              USB Cable               

• Because of the protruding joystick on the top of the controller, make sure to work on a soft surface or prop the controller up to avoid stress on the joystick.
• Place the controller face down (buttons and joystick down).
• Use a Phillips Head #1 screwdriver to remove the eight 9.65 mm screws located on the felt and metal backplate.
• Do not confuse the four screws in the rubber feet with the eight screws in the felt. The screws in the feet do not need to be removed.

Because of the protruding joystick on the top of the controller, make sure to work on a soft surface or prop the controller up to avoid stress on the joystick.

Place the controller face down (buttons and joystick down).

Use a Phillips Head #1 screwdriver to remove the eight 9.65 mm screws located on the felt and metal backplate.

Do not confuse the four screws in the rubber feet with the eight screws in the felt. The screws in the feet do not need to be removed.

1024

Step 2

• Open the door for the cord storage compartment on the right side of the device.
• Reach under the panel and push upwards on the back panel. Lift it up and remove it from the device.

Open the door for the cord storage compartment on the right side of the device.

Reach under the panel and push upwards on the back panel. Lift it up and remove it from the device.

Step 3

• With flap unlatched, gently bend the flap and pull slightly to get the pegs out of the socket
• Be sure to be gentle and not snap the plastic flap in half.

With flap unlatched, gently bend the flap and pull slightly to get the pegs out of the socket

Be sure to be gentle and not snap the plastic flap in half.

Step 4

• Slide USB cable up from the plastic barrier casing.

Slide USB cable up from the plastic barrier casing.

Step 5

• The USB cord is connected to the logic board by a plastic plug with five wires.
• Gently pull up and wiggle the white plastic end attached to the wires out of the mother board.
• The white casing on top pulls off from its counterpart on the logic board. Do not take off the bottom part of the white fixture from the logic board.
• Remove USB cable from device.

The USB cord is connected to the logic board by a plastic plug with five wires.

Gently pull up and wiggle the white plastic end attached to the wires out of the mother board.

The white casing on top pulls off from its counterpart on the logic board. Do not take off the bottom part of the white fixture from the logic board.

Remove USB cable from device.

To reassemble your device, follow these instructions in reverse order.

Cancel: I did not complete this guide.

Author

                                      with 2 other contributors 

                    Dana                     

Member since: 02/01/2015

141 Reputation

                                      1 Guide authored                  



                       Badges:
                       4







                                                        +1 more badge                           

Team

                       Cal Poly, Team 17-35, Amido Winter 2015                        

                                                  Member of Cal Poly, Team 17-35, Amido Winter 2015 



                    CPSU-AMIDO-W15S17G35                     


                                            4 Members                     


                                            5 Guides authored                     

desmond.bouey1 - Feb 26, 2017

Reply

Where do I get the USB wire?